Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

load for m1 garand

Discussion in 'Handloading and Reloading' started by Robbins290, Apr 29, 2012.

Thread Status:
Not open for further replies.
  1. Robbins290

    Robbins290 Member

    Joined:
    May 8, 2011
    Messages:
    1,255
    Location:
    Limerick, maine
    ive been loading for my remington 700 for a few years now. but i want to start reloading for my m1 garand. i speer reloading manual does not say if a load is right for the m1.
     
  2. Grumulkin

    Grumulkin Member

    Joined:
    Dec 1, 2005
    Messages:
    2,573
    Location:
    Central Ohio
    Get a Hornady manual. It has Garand specific loads.
     
  3. bbq fan

    bbq fan Member

    Joined:
    Sep 10, 2010
    Messages:
    73
    I made the Hornady book purchase just for the M1 Garand data... Plus check out the CMP forums reloading section. There's a huge amount of reloading info on their site. Good luck
     
    Last edited: Apr 29, 2012
  4. rconnerley

    rconnerley Member

    Joined:
    Apr 24, 2010
    Messages:
    2
    Ditto on the Hornady Manual. My Garand runs like a top on 46.0 gr of H4895 with 150gr projectiles.
     
  5. rg1

    rg1 Member

    Joined:
    May 26, 2006
    Messages:
    1,221
    Location:
    Kentucky
    It is widely recommended to only use powders with a burn rate from IMR 4895 to IMR 4064. Keep bullet weights from 147-175 grains. With 150 grain bullets using IMR 4895, a load from 46-48 grains with a standard LR primer is most often recommended. For accuracy shooting often they recommend 168 grain match bullets with IMR 4064 powder. I shoot military surplus M2 150gr. FMJ's with 47-47.5 grains of IMR 4895 in various 30-06 cases. Make sure primers are seated flush or below and I recommend a headspace gauge. The chambers on some or a lot of Garands are on the maximum side of spec and if you full length resize and push the shoulder back to zero every time your brass will stretch too much with shorter case life and the possibility of case separations. Check your brass closely for case stretching. Not any difference in loading for any other rifle but the Garand is a little hard on brass from long chambers plus case ejection dings or bent extractor case rims. Have fun with a fun rifle.
     
  6. ArchAngelCD

    ArchAngelCD Member

    Joined:
    Nov 25, 2006
    Messages:
    22,225
    Location:
    Northeast PA, USA
    Yep, that's a good M1 Garand ammo recipe alright. It works very well and is accurate in my M1.
     
  7. Sport45

    Sport45 Member

    Joined:
    Mar 5, 2004
    Messages:
    2,783
    Location:
    Houston, TX
    With bullets from 150 to 168gr you can pick any powder no slower than IMR4320 or faster than IMR3031.

    TAC, Varget, the 4895s, 2495, and the 4064's are all good among others. Just don't try to make a magnum out of the thing and you'll do fine.

    I found my M1 likes flat base bullets better than boat-tails, but yours may not.
     
  8. kestak

    kestak Member

    Joined:
    Jul 22, 2007
    Messages:
    1,345
    Do not reinvent the wheel. Go with I4895 or H4895 if you think temperature is an issue.
    I shot thousands of rounds with my Garands, I tried many different recipes and I always came back to I4895.
     
  9. TwoEyedJack

    TwoEyedJack Member

    Joined:
    Dec 22, 2011
    Messages:
    489
    Location:
    Southwest Idaho
    I have had good results with 50 gr. TAC and 148 gr. FMJ. TAC meters so much better than the stick powders.
     
  10. kestak

    kestak Member

    Joined:
    Jul 22, 2007
    Messages:
    1,345
    If I am not mistaken, Ramshot TAC is OUT of the pressure range for the M1 Garand.

    Please double check.
     
  11. USSR

    USSR Member

    Joined:
    Jul 7, 2005
    Messages:
    8,482
    Location:
    Finger Lakes Region of NY
    First, get yourself some 4895, either Hodgdon or IMR flavor. I use surplus IMR4895, and below are my loads:

    144gr FMJBT (M80) bullet - 48.5gr.
    155gr HPBT bullet - 47.5gr.
    168gr HPBT bullet - 47.0gr.
    174gr FMJBT (M72) bullet - 46.5gr.

    Hope that helps.

    Don
     
  12. 4895

    4895 Member

    Joined:
    Mar 6, 2011
    Messages:
    732
    Location:
    Tucson, Arizona
    Don't forget to use the NATO 7.62 primers as they are built harder and will reduce slam fires. CCI makes them for a buck or so more than standard primers. Cheap insurance if you ask me.
     
  13. Slamfire

    Slamfire Member

    Joined:
    Dec 29, 2006
    Messages:
    7,605
    Location:
    Alabama
    I shoot the same load year after year and have consistent match winning performance in my Garand.

    My load is a 168 SMK 47.0 grains IMR 4895 military cases CCI #34, recently shot Tula7.62 mm.


    Your first choice of powders should be any of the 4895 series: H4895, AA2495 or IMR 4895. These powders are so close that differences are basically lot to lot.


    [​IMG]

    [​IMG]


    [​IMG]

    [​IMG]

    For your Garand, I recommend

    You full length size with a small base die. Use RCBS water soluble case lube, spray on lubes will stick the case in your die.

    Set the shoulder back .003”, use cartridge headspace gages to set up your dies. I use Wilson, there are other good brands.

    [​IMG]

    Clean your primer pockets.

    Prime all cases by hand verify that the primer is completely below the case. Frankfort Arsenal said they set their primers zero to minus 0.005”.

    Never, ever, ever use Federal primers as they are the most slamfiring primer in the market, never use primers that are “more sensitive”. That includes "match" or "benchrest" primers as the cups on these primers are thin on top and the priming compounds tend to be more sensitive. You want insensitive primers with thick cups. I recommend CCI #34’s and Tula7.62 as both are sold a “military spec”

    Don’t crimp, don’t set your bullets to the lands, keep your chamber clean.
     
  14. Robbins290

    Robbins290 Member

    Joined:
    May 8, 2011
    Messages:
    1,255
    Location:
    Limerick, maine
    Thanks everybody
     
Thread Status:
Not open for further replies.

Share This Page