Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Marlin/Glenfield Model 60 help.

Discussion in 'Gunsmithing and Repairs' started by hcker2000, Feb 10, 2007.

Thread Status:
Not open for further replies.
  1. hcker2000

    hcker2000 Member

    Joined:
    Apr 9, 2005
    Messages:
    414
    Well I seem to be having some issues getting the riffle to cycle properly. Basically when it cycles the bolt back the spent shell is not getting ejected. I have polished the feed ramp and I did a little polishing on the Cartridge Lifter.

    I cleaned every thing up good but the pictures I have were before I cleaned the bolt up.

    I would really love to get this thing working in tip top shape again as its fun to shoot and cheap to shoot.

    If any one has any ideas after seeing the pictures please let me know.

    Pictures can be downloaded as a zip file (1.58MB) from one location or the other.

    http://h1.ripway.com/hcker2000/22lr.zip
    http://ww1.hnetinc.com:82/Downloads/22lr.zip

    Or individual pictures can be seen with these links (they are large pictures).

    Bolt1
    Bolt2
    Bolt3
    Inside1
    Inside2
    Inside3
    Inside4
     
  2. Chawbaccer

    Chawbaccer Member

    Joined:
    Feb 3, 2005
    Messages:
    1,865
    It is possibly that there is a bur on the chamber that is causing problems, Brownells sells a tool to iron them out.
    But it seems your left extractor has the tip broke off, both sides should match in wear. Get some cleaner in there and make sure that they both move back and forth freely and the springs have equal tension. Mumrich has the parts you will need.
     
  3. BSlacker

    BSlacker Member

    Joined:
    Dec 11, 2003
    Messages:
    292
    Location:
    USA
    If you have extraction problems try this. While you have the clean bolt out of the gun take a round and put it against the bolt face behind the extractors and point it down and shake a little. The extractors should hold the round in place lightly. I would replace the extractor on the right in the picture. Make sure the slots in the barrel where the extractors go are clean, use a pick to get the junk out it will be tough. Then clean the chamber no need to polish. Check to see if a round placed in the fresh cleaned chamber will drop free when the barrel is pointed up. If not you may have a dry fire burr.
    Polishing the ramp and lifter won't effect extraction or ejection.:)
    The extractors should move freely and spring back smartly when moved outward.
     
  4. DWARREN123

    DWARREN123 Member

    Joined:
    May 1, 2006
    Messages:
    1,749
    Location:
    Between TN & KY
  5. ATAShooter

    ATAShooter Member

    Joined:
    Nov 27, 2005
    Messages:
    909
    Location:
    Virginia
    HCKER

    If I shoot Wally bulk ammo in my 60 I get this problem too. I have to use CCI minimags. Also, It seems like the remington bulk has a "waxy" coating which dirties my chamber up quickly and slows the cycling speed.... Maybe this helps I hope...
     
  6. hcker2000

    hcker2000 Member

    Joined:
    Apr 9, 2005
    Messages:
    414
    I wondered about the one extractor clip being broken. Both sides seam to be the same pressure to open them.

    Now should it eject the spent casing before the bolt starts moving forward again?
     
  7. turjake

    turjake Member

    Joined:
    Dec 26, 2002
    Messages:
    10
    Location:
    Finland
    Hello,
    your rifle is incorrectly assembled. You need to have the other end of cartridge lifter spring on the narrow groove on top of the aluminum housing, not inside it as in pic 4 from inside. Case rim will hit the spring tip when bolt is retracting, and it will eject from extractor claws. If trouble persists after reassembly, try bending spring slightly upwards and file the tip flat if its rounded from wear.
     
  8. hcker2000

    hcker2000 Member

    Joined:
    Apr 9, 2005
    Messages:
    414
    holly crap I think your right. I looked at the notch in that thing and wondered for the longest time why it was there. Well I will put it up there and see if that fixes it.
     
  9. hcker2000

    hcker2000 Member

    Joined:
    Apr 9, 2005
    Messages:
    414
    Well I think thats got it. I moved the spring back to where it should be and now its ejecting like it should. At some point I will get that extractor replaced but for now I think its going to work.
     
  10. turjake

    turjake Member

    Joined:
    Dec 26, 2002
    Messages:
    10
    Location:
    Finland
    Good to hear that it works now. As you may already know, the extractor is necessary only for removal of an unfired cartridge, if you can accomplish that
    then theres no need to fix it. During firing cycle, the case will come out by pressure, not by extractor. You might try filing the hook into shape, you can't lose if you try as you're going to replace the claw anyway.
     
  11. hcker2000

    hcker2000 Member

    Joined:
    Apr 9, 2005
    Messages:
    414
    It seems to pull unfired rounds out just fine but a trip to the range will let me know if its working 100%
     
Thread Status:
Not open for further replies.

Share This Page