Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Merry Christmas to Me

Discussion in 'Handloading and Reloading' started by nordaim, Dec 26, 2003.

Thread Status:
Not open for further replies.
  1. nordaim

    nordaim Member

    Joined:
    Dec 14, 2003
    Messages:
    112
    Location:
    Amish Country, PA.
    -Frankford Arsenal Stainless Steel Dial Caliper Standard
    -RCBS Powder Trickler
    -RCBS Shell Holder #27 (.40S&W and 10mm)
    -Lyman Carbide 4-Die Set 40 S&W and 10mm Auto
    -RCBS Rock Chucker Supreme Master Kit
    -Once-Fired Brass 40 S&W Grade 3 Box of 1000
    -Frankford Arsenal Case Tumbler with Standard Media Separator Master Kit 110 Volt
    -D & J Match Grade Cast Bullets 40 S&W and 10mm (401 Diameter) 155 Grain Lead Round Nose Box of 1000

    Anything else that I should add to this order?
     
  2. stans

    stans Member

    Joined:
    Dec 27, 2002
    Messages:
    2,426
    Location:
    central Virginia
    Instead of a powder trickler, I would get a powder measure. Powder trickler's are just that, they trickle powder into a pan, literally by a few flakes or granules at a time. This is fine for precision rifle reloading where a powder measure is used to dump some powder into a pan, then the trickler is used to slowly add powder to get the charge weight up to a specified amount with absolutely no variation in the final charge weight. This is not necessary with pistols.
     
  3. uglymofo

    uglymofo Member

    Joined:
    Jan 4, 2003
    Messages:
    429
    Location:
    PRK
    Stans is right on with his advice; you don't list like you're gonna reload for rifle.

    Have you figured out your primer and powder? A good reloading manual should be on your list. Hornady, Sierra, and Lyman all have good manuals. Plastic eye protection is a requirement.
     
  4. Ala Dan

    Ala Dan Member in memoriam

    Joined:
    Dec 24, 2002
    Messages:
    12,879
    Location:
    Home Of The First Capitol Of The Confederate State
    Good info so far; but I would add a .40 cal/10mm
    case length gague form Dillon as well. Just drop
    a handloaded (complete) cartridge in, and you
    will know right quickly whether it will chamber
    in your firearm !:uhoh: Could prove to be a very
    valuable time saver? :D

    Best Wishes,
    Ala Dan, N.R.A. Life Member
     
  5. nordaim

    nordaim Member

    Joined:
    Dec 14, 2003
    Messages:
    112
    Location:
    Amish Country, PA.
    The Rock Chucker Supreme Master Kit includes a powder measure, hence I did not list that seperately, my apologies for any confusion.

    I went ahead and threw in the powder trickler because I have some .30-06, 30-30, .308, and .35 remington that I will be reloading later in 2004 as I collect dies for them, those I will more than likely buy locally. Everything listed here is in an order through MidwayUSA.

    I have Lyman's 48th reloading manual already, so that I could get acclimated to the reloading process. The RCBS RCSM Kit includes the Speer reloading manual, so I will have two to choose from at the start, intending to add more as I see the need.

    Uglymofo:

    I have a face shield that I use for when I am woodturning that I was going to use, combined with my everyday polycarb lensed glasses that I wear underneath. So eye protection is well represented.

    Powder/Primer will be bought locally once I decide on what I want, after consulting the reloading manual on the bullets that I have chosen.

    Thanks for the recommendation on a case gauge. Looking one of those up now.
     
  6. Mal H

    Mal H Administrator

    Joined:
    Dec 20, 2002
    Messages:
    17,063
    Location:
    Somewhere in the woods of Northern VA
    That's a pretty complete list, nordaim. Knowing what I know now, I would change a few items on the list if it were mine. Wish I had been able to give myownself some advice on a few items years ago. :)

    The trickler - I bought one several years ago and used it for a few months. It has sat unused for many years. It just isn't that handy a device for finishing off rifle powder loads. I use the little scoops that come with Lee die sets, in fact I bought a complete set of them over 30 years ago. One of the most useful tools on my bench. You'll find they are faster than a trickler with a little practice, and you can scoop some powder out of the pan with it if you go a little too far.

    The shell holder - Instead of the RCBS single unit, I would suggest the complete Lee set. They are machined just as well as the RCBS and you get a holder for almost any common round you will be reloading. Well worth the small difference in price.
     
  7. nordaim

    nordaim Member

    Joined:
    Dec 14, 2003
    Messages:
    112
    Location:
    Amish Country, PA.
    Will the lee shell holders work on an RCBS Press?

    That is the reason I stuck with the brand family, having never reloaded before and wanting to stick with things I know will be compatible.
     
  8. Mal H

    Mal H Administrator

    Joined:
    Dec 20, 2002
    Messages:
    17,063
    Location:
    Somewhere in the woods of Northern VA
    Yep, the only press I use them in is an RCBS Rockchucker - same press you're getting.
     
Thread Status:
Not open for further replies.

Share This Page