Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Minor Mosin Dilemma

Discussion in 'Rifle Country' started by bill larry, Apr 23, 2007.

Thread Status:
Not open for further replies.
  1. bill larry

    bill larry Member

    Joined:
    Jan 12, 2007
    Messages:
    443
    Location:
    San Antonio, Texas
    I need some opinions from you guys.

    I have been wanting to scope one of my M44's for a while in the scout manner. I plan on using the S&K insta-mount so as not to premanently alter the gun. However, I have run into a major inconvenience in my little project. I wanted to remove the bayonet to reduce wieght and improve handling.

    Great, except that my bayo is staked in place.

    What can I do? Can a gunsmith drill out the staked screw without totally screwing up the bayonet mount? Do I need to forget it, and just get a different gun? This is killing me as this Mosin is unissued and is absolutely beautiful...I really wanted to use it as a scout rifle sans bayonet.

    Thanks
     
  2. Mike U.

    Mike U. Member

    Joined:
    Feb 22, 2007
    Messages:
    690
    Location:
    Oz, right next door to The Lollipop Guild HQ
    Do you mean it was peened into place?
    If so, I had this problem too. I tried a good squirt of WD-40, let it sit for an hour, used the correct size large screwdriver plus a very determined turn and that popped it loose.
    Use whatever quality penetrating oil you have on hand. I know there are better penetrating oils out there than WD-40.

    The correct size screwdriver really helps here. One that fits that slot perfectly and is big enough for you to get a really good grip on.
    I hope it works for you.
     
  3. Cosmoline

    Cosmoline Member

    Joined:
    Dec 29, 2002
    Messages:
    23,648
    Location:
    Los Anchorage
    Kroil should work, but why not just pop the whole assembly off? If you're putting a scout scope on, you don't really need it. You should be able to kroil the pins and pop them out with a properly sized brass punch, then kroil and tap off the whole thing--including the peened bayonet. It's not a bad idea to do it once a century to check for rust, anyway.
     
  4. bill larry

    bill larry Member

    Joined:
    Jan 12, 2007
    Messages:
    443
    Location:
    San Antonio, Texas
    Okay, Cosmo, I'm going to try your suggestion once I get the correct punch. Just one pin, right? Or is the one under the sight base needing to be removed also? Thanks again!
     
  5. telomerase

    telomerase Member

    Joined:
    Mar 11, 2003
    Messages:
    3,263
    Location:
    The bear-infested hills of Grafton NH
    Hey, it's not 2044 yet! Seriously, what's the best rust-preventative finish to put on a "shooter" grade M44?
     
  6. MHBushmaster

    MHBushmaster Member

    Joined:
    Dec 15, 2006
    Messages:
    175
    Buy an M38, problem solved.
    and while your out, might as well pick up a 91/30 as well, cause you are going to sooner or later and it might as well be sooner as they are not getting cheaper;)
     
  7. Cosmoline

    Cosmoline Member

    Joined:
    Dec 29, 2002
    Messages:
    23,648
    Location:
    Los Anchorage
    Two pins, actually. If you have a gunsmith punch set and use kroil it should work fine. Otherwise it can get tricky. Actually it can get tricky anyway, thinking back on it. But sometimes it works smooth.

    I've had good results sealing the inside of the stock and under the handguard with a light grease. The Finnish Civil Guard used pine tar paste. The exposed metal is fine with CLP and periodic cleanups. Danger zones are around the receiver inside the lip of the stock, where beads of water can collect. Injecting a thin layer of grease in those cracks helps keep water out. A coat of gunstock wax over the whole sheebang is good, too. But keep in mind this is for taking the Mosin out in very wet woods, not just to the range.
     
Thread Status:
Not open for further replies.

Share This Page