Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

My 1860 colt repro is developing a problem?

Discussion in 'Blackpowder' started by ARENAMAN, Apr 3, 2009.

Thread Status:
Not open for further replies.
  1. ARENAMAN

    ARENAMAN Member

    Joined:
    Dec 16, 2008
    Messages:
    9
    Location:
    EAST TEXAS
    I've begun having a problem with my Centaure. It started with one cylinder, but today four out of six of the cylinders failed to fire. The cap didn't fire each time. I have noticed that it seems that the cylinder has begun to have room to move a little between the frame and the barrel assembly. It slides back and forth along the arbor a very small fraction of a millimeter. I think this is the problem that is causing the caps not to ignite when the hammer falls. The cylinder has moved forward from its right place against the frame enough to keep the hammer from hitting the cap firmly. I was really having a problem with that one cylinder that was the first to begin misfiring. I finally had to get a small piece of wood and place it in from of the bottom part of the cylinder and then use the loading arm and piston to press against the wood and the cylinder which firmly pressed the cylinder back against the frame. I pressed against a tree in order to put a little pressure on the end of the loading arm so that my hand would not be forward of the cylinder as I pulled the trigger. When I used this method to hold the cylinder back against the frame the stubborn cylinder fired the first time, and with the same cap I had been trying to cause to fire before.

    Does anyone know why the cylinder is now a little loose in the frame? I have checked the wedge and it seems to be all the way in and it seems to be tightly in place. I even tried to tap it in a little more and this didn't help. The place at the bottom where the barrel assembly and the frame meet is well seated together. Is there a small shim or spacer that I may have lost in the last cleaning? Any advise would be appreciated.

    I also had something else interesting happen today. An older gentleman and friend of mine gave to me an old can of FFG Holy Black, and I tried it out today. My friend told me that this powder was pretty old and might not fire very well. When I tried it today it barely made a pop in my gun and lobed a little fire ball out the end of the barrel. I think the fireball was my lube pill burning. I thought I had read that black powder didn't get old. Maybe not. I don’t think it was damp. My friend said he had stored it inside, and so did I.
     
  2. BPR

    BPR Member

    Joined:
    Apr 15, 2008
    Messages:
    36
    Location:
    CA Bay Area
    Any chance pieces of a fired caps are falling down and wedging between the hammer and the frame? It happen to me several times and the liitle buggers are hard to see. They hold the hammer just enough that it won't strike the cap hard enough to fire. Try the old movie trick, raise the revolver high in the air before you cock it so the fired cap will fall away. As far as a washer or spacer, I've never seen one. The only problems I've seen like your describing have been with kit builds. Finally had to get a new frame.
     
  3. ARENAMAN

    ARENAMAN Member

    Joined:
    Dec 16, 2008
    Messages:
    9
    Location:
    EAST TEXAS
    It might have been a cap fragment. I didn't see anything when I was shooting. But didn't look specifically at the slot where the hammer falls. AND there was a cap fragment that fell out of the hammer area as I was taking the gun apart for cleaning just after making my initial post. It may have been there the whole time. OR, it may have been the last cap fired.
     
  4. Old Fuff

    Old Fuff Member

    Joined:
    Dec 24, 2002
    Messages:
    23,908
    Location:
    Arizona
    The wedge shouldn't be driven all of the way in. If it is it needs to be replaced. A properally fitted wedge will just come through to the side of the barrel on the right side.

    And it would be advisable to compeletly tear the lockwork down, inspect it, and be sure it's clean and lubricated before you but it back together. If you don't know how, instructions are posted at the begining of the Blackpowder Shooting sub-forum.
     
  5. mykeal

    mykeal Member

    Joined:
    Sep 9, 2006
    Messages:
    5,147
    Location:
    Michigan
    I don't agree with Old Fuff on the wedge position. In my opinion a properly fitting wedge is one in which the cylinder to forcing cone clearance is between 0.006" and 0.010", regardless of where the wedge lines up.
     
  6. madcratebuilder

    madcratebuilder Member

    Joined:
    Jul 15, 2007
    Messages:
    5,020
    Location:
    Northern Orygun
    You should not use the wedge to control barrel gap. That is the job of the arbor/barrel fit.
    Fuff is correct, the wedge should just slightly protrude from the right side.

    Have you inspected the arbor and frame at the recoil shield? It sounds like the arbor has moved forward.
     
  7. scrat

    scrat Member

    Joined:
    Jan 27, 2007
    Messages:
    6,882
    Location:
    Monrovia, CA
    I am against slamming your gun against a tree and forcing something in to make it fire.

    3 things to do.
    go to vti gun parts order a new wedge and some new nipples

    take apart the guns internal works clean them very good. Next take a small piece of leather and put it under the main spring towards the bottom to give a little more rigidness. Then when parts come in replace the nipples and replace the wedge. Then go back to the range and try it out again.
     
  8. madcratebuilder

    madcratebuilder Member

    Joined:
    Jul 15, 2007
    Messages:
    5,020
    Location:
    Northern Orygun
    You may want to check the threads on this Belgium made Colt before you order Italian parts. I believe the fasteners are different threads, possibly the nipples too.
     
  9. ARENAMAN

    ARENAMAN Member

    Joined:
    Dec 16, 2008
    Messages:
    9
    Location:
    EAST TEXAS
    Good advise scrat, advise which i will follow.

    But, let me be clearer in my description of what did to make the gun fire. I did not slam anything against a tree. I placed a piece popsickle stick between the loading ram and the front of the cylinder and lowered the loading lever and gently pressed the end of the lever against the tree in order to press the cylinder back firmly against the frame while i pulled the trigger. This worked because the cap fired this time after i had tried at least a dozen times before to make that same cap fire.
     
  10. ARENAMAN

    ARENAMAN Member

    Joined:
    Dec 16, 2008
    Messages:
    9
    Location:
    EAST TEXAS
    Advice, advice, i spelled advice wrong.
     
  11. scrat

    scrat Member

    Joined:
    Jan 27, 2007
    Messages:
    6,882
    Location:
    Monrovia, CA
    Yep if it were my gun i would for sure do what i wrote. what does not make sense is the fact that it only started happening on one cylinder. When this happens i usually think nipples first. Then main spring for firmness then wedge for tight cylinder fit.
     
  12. ARENAMAN

    ARENAMAN Member

    Joined:
    Dec 16, 2008
    Messages:
    9
    Location:
    EAST TEXAS
    From what i've read you need to have a gunsmith's tools in order to make ready a nipple to fit the belgium made colt.
     
  13. scrat

    scrat Member

    Joined:
    Jan 27, 2007
    Messages:
    6,882
    Location:
    Monrovia, CA
    That may not be true. Just take me a few minutes to tell you. Basicly you need some guages to be able to tell the thread pitch and diameter of the nipple. Once thats done then you need to go shopping. i dont remember the site one of the other guys may though. there is a site that shows all the different thread pitches for nipples and part numbers.
     
  14. madcratebuilder

    madcratebuilder Member

    Joined:
    Jul 15, 2007
    Messages:
    5,020
    Location:
    Northern Orygun
    They use a standard revolver nipple wrench.
    This is an original style
    This style is probably more serviceable.
     
  15. whosyrdaddy

    whosyrdaddy Member

    Joined:
    Aug 12, 2006
    Messages:
    332
    MCB, could you point me to your source supporting this statement?
     
  16. madcratebuilder

    madcratebuilder Member

    Joined:
    Jul 15, 2007
    Messages:
    5,020
    Location:
    Northern Orygun
    I sounds like you have excessive cylinder end play, much more than the normal .006-.012. Just how much end play do you have? I think it may be unsafe to fire if you have to wedge a stick in it the hold the cylinder in place.
     
  17. whosyrdaddy

    whosyrdaddy Member

    Joined:
    Aug 12, 2006
    Messages:
    332
    ARENAMAN, there is a very easy way to tell if the cap fragment was the problem. Simply place caps on all 6 nipples and see if they fire the first time around now. Let us know.
     
  18. madcratebuilder

    madcratebuilder Member

    Joined:
    Jul 15, 2007
    Messages:
    5,020
    Location:
    Northern Orygun
    Read David Chicoine's book "Gunsmithing Guns of the Old West"
     
  19. whosyrdaddy

    whosyrdaddy Member

    Joined:
    Aug 12, 2006
    Messages:
    332
    I have, thanks. I have also read the original colt patent that seems to contradict this info and I thought perhaps someone could show me where Samuel L. Colt changed his mind along the way.
     
  20. Old Fuff

    Old Fuff Member

    Joined:
    Dec 24, 2002
    Messages:
    23,908
    Location:
    Arizona
    I agree, but what do you do if the tapered wedge is in as far as it can go, and you still have excessive cylinder/barrel gap?

    Too many folks who don't understand how the system is supposed to work think that the wedge is supposed to be driven in all of the way. So they drive it in. This may or may not close the gap to the point where the cylinder won't turn. But if the cylinder does turn, and for what ever reason the gap opens up to the point where the hammer won't detonate the caps, there isn't any adjustment left - except to replace the wedge with a new one.
     
  21. madcratebuilder

    madcratebuilder Member

    Joined:
    Jul 15, 2007
    Messages:
    5,020
    Location:
    Northern Orygun
    Perhaps after 160 years of maintaining and rebuilding these cap and ball revolvers some have found a better way.
     
  22. whosyrdaddy

    whosyrdaddy Member

    Joined:
    Aug 12, 2006
    Messages:
    332
    I could not agree more, and I was deeply saddened by the passing of William B. Ruger.
     
  23. ARENAMAN

    ARENAMAN Member

    Joined:
    Dec 16, 2008
    Messages:
    9
    Location:
    EAST TEXAS
    I just placed six caps on the gun and tried it again and 5 out of six fired right off. I guess my problem was a spent cap in the way all along. Thanks for the idea whosyrdaddy. The one cylinder that did not fire probably needs to have its nipple backed out a little. I used my finger this time to press the cylinder back against the frame and that stubborn cylinder fired when it wouldnt fire before. I am a newbie and have gotten around to getting a nipple wrench. I know i need one for proper cleaning so i will get one soon.
     
  24. mykeal

    mykeal Member

    Joined:
    Sep 9, 2006
    Messages:
    5,147
    Location:
    Michigan
    I do not dispute the fact that adjusting the arbor/cylinder/barrel interface, especially on Uberti guns, can significantly improve the cylinder end play and make the wedge fit/function better.

    However, I believe that the majority of Colt replica revolver owners are much more able to place the wedge to get a range of measured end play, and then replace the wedge if this is not sufficient, than they are to perform the tasks necessary to revise the arbor/wedge geometry. That was the basis of my post.
     
  25. scrat

    scrat Member

    Joined:
    Jan 27, 2007
    Messages:
    6,882
    Location:
    Monrovia, CA
    Nipples, Wedge, Tighten mainspring
     
Thread Status:
Not open for further replies.

Share This Page