Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

my new 870

Discussion in 'Shotguns' started by tango3065, Jan 29, 2003.

Thread Status:
Not open for further replies.
  1. tango3065

    tango3065 Member

    Joined:
    Jan 19, 2003
    Messages:
    851
    Location:
    Kentucky
    My rem 870 i gave 145.00 bucks for it was a camo stock but iredone the wood myself also its gettingbead blasted and blued this week for 40.00 not to bad for a 870 turkey express for a total of 185.00 I hope the pics work
     
  2. 10-Ring

    10-Ring Member

    Joined:
    Dec 24, 2002
    Messages:
    12,037
    Location:
    California
    Congrats! Good price too ;)
     
  3. tango3065

    tango3065 Member

    Joined:
    Jan 19, 2003
    Messages:
    851
    Location:
    Kentucky
    Also the wood stock serves it well but how will it hold up, like rot warp that kinda stuff, also i had to use a lot of paint remover to get all the camo paint off from it will this be a problem in the the wood? I guess im wondering if i should put a synthetic on it like my mossy has.
     
  4. Dave McCracken

    Dave McCracken Moderator In Memoriam

    Joined:
    Dec 20, 2002
    Messages:
    13,938
    Location:
    MD.
    I've done a coupla inexpensive stocks with a stain and satin finish Varathane. Not complicated, I'm no great shucks as a woodworker.

    Stocks should be sealed against the elements. This includes the end grain.

    Nice buy, now BA/UU/R....
     
  5. redneck

    redneck Member

    Joined:
    Dec 26, 2002
    Messages:
    1,154
    Location:
    Ohio
    The simplest way to finish a stock is watcos danish oil. I would use the natural color instead of one of the ones with stain mixed in. It will darken the wood a fair amount and bring out its natural color.
    Pretty simple, sand the wood down to 150 grit, pay close attention places where the end grain is exposed. Shake the can of finish really well, and using an old T shirt or some other kind of rag start wiping on a heavy coat. Wipe it on until its uniformly wet and no more is soaking in. Wring out the wrag and wipe it down again so that there is just a thin layer on the wood and no runs. Leave it to dry, depending on the wood and the humidity it could take anywhere from an hour to a day.
    LIGHTY (don't put much more effort into it than wiping the finish on, just scuff it up, only sand heavily on spots where the grain has raised) sand the wood down again with 320 grit paper, spend most of your time on the end grain it has a tendency to raise a little.
    Wipe on another light coat of watcos, and leave it to dry.
    If the grain is raised or it doesn't seem to be taking it evenly, lightly sand again with 400 grit or more 320. And wipe on another coat, then let it dry.
    This time you should be able to buff it out with a dry cloth and it should look pretty nice. You can put more coats on if you want, but 3 should offer pretty good protection.
    Then maybe once a year wipe it down with another coat, you'll have plenty left from the first can.
    It sounds kind of involved but its just a matter of sanding and wiping the stuff on. Clean up is easy, you don't need any solvents, and the results are good. The color change in the wood is pretty consitent from one type to another. You get a nice penetrating finish that will repel water and gives a little bit of a shine. Its cheap too :D
     
  6. Kahr carrier

    Kahr carrier Member

    Joined:
    Dec 30, 2002
    Messages:
    2,060
    Location:
    WESTSIDE
    Looks good. Good price also.:)
     
  7. Guyon

    Guyon Member

    Joined:
    Dec 25, 2002
    Messages:
    820
    Location:
    Over Yonder, Tennessee
    $40 for blasting and blueing is a good price too. Enjoy the new gun.
     
Thread Status:
Not open for further replies.

Share This Page