Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

My S&W 6906 makeover

Discussion in 'Handguns: Autoloaders' started by daledut, May 11, 2012.

Thread Status:
Not open for further replies.
  1. daledut

    daledut Member

    Joined:
    May 11, 2012
    Messages:
    10
    Location:
    Ohio
    I recently obtained a Police trade in S&W 6906 off of Gunbroker. The outside had some holster wear and a scuff or two, but the inside looked like brand new. I have always liked the two-tone look so I decided to take it down to the frame and paint it low gloss black.
    This was my first attempt at complete disassembly of a firearm. I actually got it back together and functioning and I think it turned out not looking half bad for an amatuer attempt. See attached photos (before on left, after on right).
    Oh yeah, I also did a hand brush finish on the slide and polished the trigger, hammer, slide lock lever, safety levers and exposed pins.
    All comments welcome.

    dale
     

    Attached Files:

    Last edited: May 11, 2012
  2. bannockburn

    bannockburn Member

    Joined:
    Apr 24, 2007
    Messages:
    13,750
    Looks pretty decent. What kind of paint did you use and how was it applied? I think my concern would be how well it holds up with normal handling and use.
     
  3. mesinge2

    mesinge2 Member

    Joined:
    Feb 12, 2009
    Messages:
    2,219
    Location:
    Central Florida
    Nice work, I like the two tone look!
     
  4. smalls

    smalls Member

    Joined:
    Feb 8, 2011
    Messages:
    2,433
    Location:
    Macomb County, MI
    That looks great! I love the two tone look.

    I have the same concern bannockburn has, is what kind of paint you used?
     
  5. daledut

    daledut Member

    Joined:
    May 11, 2012
    Messages:
    10
    Location:
    Ohio
    Isaw on a gun thread somewhere that a guys used Automotive Engine paint (no bake type) and has for many years with good success. I figured since I bought this as a knock around gun, I couldn't hurt it much. The can said that it fully cures in 7 days. I hand sanded the frame with 400 wet dry paper and sprayed it on (3 coats) then waited for 7 agonizing days.
    Time will tell if it holds up. I figure if it doesn't hold up then I will take it apart again and send it to a pro, but in the meantime I have about $12 for paint and sandpaper into the finish. And it was fun to do.
     
  6. TennJed

    TennJed Member

    Joined:
    Sep 26, 2010
    Messages:
    3,454
    Please keep us updated on this. I too have seen people posting about using engine paint on guns with sucess. I would like to see some picture examples of how it holds up.

    I have considered trying out on a knock around gun my self
     
  7. daledut

    daledut Member

    Joined:
    May 11, 2012
    Messages:
    10
    Location:
    Ohio
    Okay here is the update already. The painting portion of this experiment is a failure. I went out back to shoot the pistol for the first time after paint cured. I notice that the paint was rubbing off of the beaver tail after only 24 rounds. I then discovered that I could scrape the paint off with a finger nail. See attached photo.
    I sanded that portion down and am doing some touch up but once I save my pennys I am going to send it to someone who knows what they are doing.
    So unless you are a better painter than I (which wouldn't take much) I would stay away from the engine paint.
    BTW I LOVE the way this pistol shoots. I hardly even notice the recoil as compared to my Ruger LC9.
     

    Attached Files:

Thread Status:
Not open for further replies.

Share This Page