Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Need help w/ Vaquero

Discussion in 'Handguns: Revolvers' started by texas chase, Aug 3, 2008.

Thread Status:
Not open for further replies.
  1. texas chase

    texas chase Member

    Joined:
    Sep 19, 2006
    Messages:
    309
    Location:
    Central Texas
    I'm trying to install a new spring kit into an "old" Ruger Vaquero. I tried the method of taking the grips off, insert pin, and pull the spring mechanism out BUT... I couldn't get the mainspring mechanism out. (Yes, I've read the manual but it hasn't helped at this point.)

    So, I tried a total disassembly and got as far as removing the grip frame from the cylinder frame. I then decided that this was just too much at this point and wanted to put it back together. Seems simple enough right? Well, I can't get the grip frame back on to the cylinder frame.

    I would appreciate any help. Photos are REALLY APRECIATED.

    Thanks
     
  2. Virginian

    Virginian Member

    Joined:
    Apr 7, 2003
    Messages:
    3,971
    Location:
    Williamsburg, Virginia
    Gotta get the trigger spring in above the small ledge on the trigger.
     
  3. calaverasslim

    calaverasslim Member

    Joined:
    Jul 20, 2005
    Messages:
    1,006
    Location:
    San Antonio de Bejar
    Yep!

    Ben there, dun that and got the T shirt. :D

    It say........toopid..:what:


    I went the route you took and I shore wisht you had talked to me first. Wudda tole you doan try that.:banghead::banghead::banghead:


    I have a friend that is a great gunsmith and the best part is he is free. He put mine back together for me. Never tried that again.:neener:

    Your down around San Antonio, let me know. I'll introduce you to him.:rolleyes:
     
  4. mtngunr

    mtngunr Member

    Joined:
    Jun 6, 2008
    Messages:
    458
    Location:
    SEUS
    OK....you DID cock the hammer, inserted the pin in the base of the strut, then DEcocked the hammer to relieve tension before trying removal?

    Ditto the above trigger spring comment....also checking to see if you did leave the pin in the strut while trying to remove the grip-frame?
     
  5. texas chase

    texas chase Member

    Joined:
    Sep 19, 2006
    Messages:
    309
    Location:
    Central Texas
    oops...

    Virginian- how do I that?

    Mtngunner- I think you found my main problem. I did not put the pin in the spring lock before trying to disassemble... the second time. Now what do I do?

    Thanks for the help- I really appreciate it.
     
  6. mtngunr

    mtngunr Member

    Joined:
    Jun 6, 2008
    Messages:
    458
    Location:
    SEUS
    If its a big old Vaquero, there is no spring lock, only the strut, seat, and spring....you'll need to put those three back together again outside the gun WITH the pin holding them together....what I have done is to use a vise with soft jaws to hold the strut, then compressed the spring with dikes/cutters opened just enough to clear the strut, and then placed seat and pin while holding the spring compressed....this is dangerous, and the spring could fly out and blind you or get lost forever...be careful...or, just fight like heck to get the strut in the hammer recess and it all held together until you can get a couple of screws started....hope you have a wife you're on good terms with, as this is a three hand task.

    The trigger return spring is easiest dealt with by unhooking it from the rear on both sides, positioning it correctly during assembly, and then rehooking the rear two legs after the gripframe is installed...
     
  7. texas chase

    texas chase Member

    Joined:
    Sep 19, 2006
    Messages:
    309
    Location:
    Central Texas
    OK, half way there...

    Alright! I got the strut, spring, and seat (yes, its an old model vaquero) out of the grip frame. I got the new spring on the strut with the seat AND PIN in place. And I got grip frame back on the cylinder frame. But... I can't get the spring/strut/seat back into the gun!?! Help!
     
  8. mtngunr

    mtngunr Member

    Joined:
    Jun 6, 2008
    Messages:
    458
    Location:
    SEUS
    Make sure you've got everything pointed the correct direction...seat down, strut ball-end up, upper angle of strut forward...hammer fully forward for install of strut, ball end in hammer base recess, hammer then cocked for pin removal....
     
  9. Virginian

    Virginian Member

    Joined:
    Apr 7, 2003
    Messages:
    3,971
    Location:
    Williamsburg, Virginia
    If the trigger spring legs are unhooked, you may need to hook them up and get them out of the way to squeeze in the hammer spring and strut. Make sure the upper end of the strut is in the slot in the hammer or you will never get it.
     
  10. texas chase

    texas chase Member

    Joined:
    Sep 19, 2006
    Messages:
    309
    Location:
    Central Texas
    thanks

    I got everything back together with new springs installed last night. Thanks for all the help fellas.

    She works like a champ!
     
Thread Status:
Not open for further replies.

Share This Page