Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

No serial number - how to ID for insurance?

Discussion in 'General Gun Discussions' started by Gtimothy, Mar 19, 2012.

Thread Status:
Not open for further replies.
  1. Gtimothy

    Gtimothy Member

    Joined:
    Aug 21, 2010
    Messages:
    417
    Location:
    South West Florida
    I have an old Stevens Model 56 Buckhorn .22 that I've had for 46 years but has no serial number. Apparently no serial numbers were used on some "inexpensive" rifles back when this gun was manufactured. Is there a proper way to mark it for identification purposes? I don't want to screw it up. It isn't a "valuable" gun except for sentimental reasons...It was my first gun. Help?
     
  2. Jorg Nysgerrig

    Jorg Nysgerrig Member

    Joined:
    Apr 13, 2006
    Messages:
    7,823
    About all you can do is take pictures of it and describe it as fully as possible including whatever information is on it. Check with your agent to see if that will suffice or if they need more. Different policies have different requirements. That said, since it's not actually worth that much, I don't think it will be a big deal either way.
     
  3. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    Take the butt-plate off, or the action out of the stock and write your name & address under there on the wood with a lead pencil.
    Crack-head burglers aren't smart enough to even look under there.

    If it is stolen, you can tell the cops how to ID it if it is recovered.

    From a collector standpoint, the markings can be easily removed from the wood if necessary.

    rc
     
  4. Gtimothy

    Gtimothy Member

    Joined:
    Aug 21, 2010
    Messages:
    417
    Location:
    South West Florida
    I've got the pictures and will take rcmodel's advice and use my "last 4" and initials under the buttplate in pencil! Clever!!!!! That's why I ask questions here!:D
     
  5. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    Name & address contact info might be better.

    You are in FL, and a cop in TX who might recover it wouldn't have a clue who the last four and initials belong too.

    rc
     
  6. Gtimothy

    Gtimothy Member

    Joined:
    Aug 21, 2010
    Messages:
    417
    Location:
    South West Florida
    You have a point! Again, I wasn't thinking outside the box! :eek:
     
  7. SlowFuse

    SlowFuse Member

    Joined:
    Mar 31, 2011
    Messages:
    1,059
    Location:
    Heart of Dixie
    I'm not sure if its actually cheap guns, but a lot of firearms before 1968 didn't have serial numbers. I also have an old Stevens single shot that applies, along with a few others. I believe a law/act was passed to start serial numbering all firearms after that specific year.
     
  8. browneu

    browneu Member

    Joined:
    Mar 26, 2004
    Messages:
    739
    Location:
    ohio
    I didn't supply serial numbers to insurance for additional coverage. I just gave them a list of my firearms and their replacement values.
     
  9. Gtimothy

    Gtimothy Member

    Joined:
    Aug 21, 2010
    Messages:
    417
    Location:
    South West Florida
    The serial numbers are for me, the insurance company hasn't asked for them. I just want them all recorded in case of theft for the authorities. I just wasn't sure how to go about marking it so it could be identified as mine. I have several OLD guns that were passed down from my Grandpa and father but this is the only one I have that had no serial #.
     
  10. medalguy

    medalguy Member

    Joined:
    Mar 20, 2009
    Messages:
    3,214
    Location:
    New Mexico
    Photos are great, but be sure to note any definitive scratches, dents, or other marks that could be used to positively ID the weapon. Without a serial number, a listing in NCIC is pretty hard to connect.
     
  11. fpgt72

    fpgt72 Member

    Joined:
    Aug 2, 2011
    Messages:
    1,289
    I do close to this...but use a sharpie and white medical tape....there are also other places to hids stuff on different guns.
     
  12. 303tom

    303tom member

    Joined:
    Jul 16, 2011
    Messages:
    4,059
    Location:
    Missouri
    I put a number on mine.............
     
  13. Black Butte

    Black Butte Member

    Joined:
    Jun 21, 2008
    Messages:
    888
    Electropencil :evil:
     
  14. SlowFuse

    SlowFuse Member

    Joined:
    Mar 31, 2011
    Messages:
    1,059
    Location:
    Heart of Dixie
    I use a handheld engraver to put my name or at least initials in an out of sight spot... Magazine floor plates, receiver interiors etc. I tried to stay away from areas under any major stress. I practiced on scrap metal a lot before touching anything that mattered. I like the electropencil idea too.
     
  15. medalguy

    medalguy Member

    Joined:
    Mar 20, 2009
    Messages:
    3,214
    Location:
    New Mexico
    Uhhh... I've seen some otherwise very expensive guns offered real cheap because someone engraved his DL number in the barrel or receiver. That's a very good way to absolutely ruin the value of any firearm. Whoever invented the engraving pen should have a very special place in Hell.
     
  16. BCCL

    BCCL Member

    Joined:
    Feb 3, 2009
    Messages:
    1,438
    Location:
    So. Illinois
    I've tried to decide what to do with a similar gun, after my older brother passed away in Dec. 2010, his widow gave me an old Springfield .22 semi auto that belonged to my father, and my brother inherited it when Dad passed away in 1977.

    I has no serial number, and since it's an Heirloom gun that has no chance of ever being sold outside the family, and pretty much zero collector value, and will for sure go to my great-nephew when I go, I've considered wood burning our last name into the stock or something similar.
     
  17. highlander 5

    highlander 5 Member

    Joined:
    Sep 15, 2006
    Messages:
    2,344
    Location:
    lynn,ma
    Where I worked we used a device that I called an electro etch. Used a stencil that you type the info on serial no,part no. then a pad was soaked in an mild acid solution and an electric current etched the info on the part. Much neater and professional looking than an engraving pencil and the only way to remove it is to grind it off. Check some of the local machine shops they may have the machine and will put your name and other info for short money or free
     
  18. SlowFuse

    SlowFuse Member

    Joined:
    Mar 31, 2011
    Messages:
    1,059
    Location:
    Heart of Dixie
    I have the same theory as BCCL. I wouldn't do it to a collector grade firearm. All of mine are "working guns" not show pieces.
     
Thread Status:
Not open for further replies.

Share This Page