Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

noob ? about lead bullets

Discussion in 'Handloading and Reloading' started by xsquidgator, Apr 27, 2007.

Thread Status:
Not open for further replies.
  1. xsquidgator

    xsquidgator Member

    Joined:
    Jan 14, 2007
    Messages:
    836
    I'm new to reloading, and have only made one or two small batches of .38Special so far using a friend's button nosed, lead bullets.

    Today I got my shipment of my own lead bullets (the FMJ bullets are on backorder), several hundred each of .38 SWC lead bullets and 9mm lead roundnose bullets.

    These bullets did not come lubed (the boxes don't say they are anyway) and I doubt they are. From what I read, I could go ahead and load these but I'd probably get excessive leading of the bore. Is this right? I didn't buy any bullet lube and will have to go find some I suppose... I was really motivated to load up a couple dozen each of these and go try them out tomorrow. Should I get lube first? My reloading manuals talk about lubing in the context of cast lead bullets, but they seem to stop short of saying you HAVE to do it. Opinions and experience with lead bullets for .38 special and 9mm?
     
  2. qbpc

    qbpc Member

    Joined:
    Apr 21, 2007
    Messages:
    191
    Location:
    Gulfcoast
    What do you have?

    Are the lead bullets hard cast and have a blue, green, or red stripes around them this is the lube.
    BB
     
  3. velosa

    velosa Member

    Joined:
    Feb 18, 2006
    Messages:
    23
    I would definately not shoot any cast bullet without lube. It is just not worth it. That's not to say that I haven't done it before, but the leading was so bad in the barrel that you couldn't hit anything at 25 yds. after a 8-10 rounds being fired. Takes all the fun out of it. Plus, that level of leading is a real bear to clean. Take my advice and go online and order a lube-o-matic, a sizing die, and some red rooster lube and do it right.
     
  4. Hazzard

    Hazzard Member

    Joined:
    Sep 1, 2006
    Messages:
    394
    If the bullets don't have blue, green red, orange, etc. bands around them they are not lubed. You can buy a bottle of Lee liquid alox and follow the tumble lube directions. It works pretty well and does not require the expense of a lubrisizer. If they do have the colored bands then load and shoot.
     
  5. xsquidgator

    xsquidgator Member

    Joined:
    Jan 14, 2007
    Messages:
    836
    Ah, thanks for the explanation. These bullets do not have the colored bands and are thus certainly not lubed. (My friend's bullets I was using did say they were lubed, and they did have blue bands around the shank)

    Liquid alox it will probably be then.
     
  6. scrat

    scrat Member

    Joined:
    Jan 27, 2007
    Messages:
    6,882
    Location:
    Monrovia, CA
    for sure lube them.
     
  7. Hazzard

    Hazzard Member

    Joined:
    Sep 1, 2006
    Messages:
    394
    One final piece of advice would be to check the OD of the bullets to see if they need sized. I believe that .38 specials should be .358 for lead but others may be able to give better advice on them as it is not a caliber that I load. If they are not sized correctly a Lee sizer die will work fine and they are pretty inexpensive. They won't size benchrest quality stuff, but will do for most purposes.
     
  8. LHB1

    LHB1 Member

    Joined:
    Feb 7, 2005
    Messages:
    873
    Location:
    Houston
    Hint: Next time I would make sure the cast lead bullets were SIZED AND LUBED before you got them. Kind of a pain to do it yourself unless you have your own sizer/lube equipment. I have always cast, sized, lubed my own bullets and didn't know anyone sold cast bullets without sizing/lubing them before delivery to customer.

    Good shooting and be safe.
    LB
     
  9. tasco 74

    tasco 74 Member

    Joined:
    Feb 25, 2004
    Messages:
    855
    Location:
    iowa u.s.a.
    i have bought hornady .38 cal wcs before and they had some kind of black lube on em.... there were no lube grooves as it were just three shallow serated looking grooves....... they shot real good and were very accurate..... are your bullets kinda black??
     
  10. cdrt

    cdrt Member

    Joined:
    Mar 12, 2007
    Messages:
    949
    Location:
    The Lone Star State
    You never mentioned what brand of bullets. Some, like Speer, etc. use a swaging process rather than casting. The bullets are coated with a lube rather than using the lube rings. If these are Speers, etc. they may be lubed already.
    I sent you a PM about this as well.

    Navy Vet & SWIFT Boat OIC
     
  11. trickyasafox

    trickyasafox Member

    Joined:
    Dec 22, 2004
    Messages:
    2,523
    Location:
    upstate NY go to school in WNY
    yea post the make of the bullets, unless im really off base, you have to seek out non lubed lead bullets, in my experience they are the exception not the rule.
     
  12. Sunray

    Sunray Member

    Joined:
    May 17, 2003
    Messages:
    11,279
    Location:
    London, Ont.
    "...excessive leading of the bore..." That's caused by trying to drive a cast bullet too fast. Lubed or not.
    Are these bullets swaged by any chance? Swaged bullets usually don't have the ring of lube. The box should say if they are swaged or cast.
     
  13. CZ57

    CZ57 member

    Joined:
    Jan 6, 2005
    Messages:
    1,533
    Location:
    Heart of Texas
    Well, it's definitely caused by trying to drive a swaged bullet too fast. Usually as soon as you get above sub-sonic velocity. If a hard cast bullet is properly sized to the bore and has a BHN of 18 or higher, leading isn't much of an issue. Oregon Trails bullets take this a step furhter with their alloy that yields a BHN of 26 with many of their bullets. Most commercial casters use an alloy that yields a BHN of 18 +/- 1.

    X: You may have ordered Swaged lead bullets.;)
     
  14. Walkalong

    Walkalong Moderator

    Joined:
    Nov 20, 2006
    Messages:
    48,436
    Location:
    Alabama
    I have never seen commercial lead bullets that did not come lubed. I guess they are out there. Strange. They may have some type of lube on them other than the traditional lube in lube grooves. (like Rooster Jacket or Tumble Lube types).

    If they are not lubed at all they willl definitely lead your barrel to some degree or another.

    Also, remember, just getting hard cast bullets will not guarentee no leading. The bullets can be too hard for the pressure/velocities you are shooting at as well. You are loading the 9MM and the .38 Spl. which are very far apart in pressure generated and also you are dealing with chamber throats with the .38 Spl. where you are not with the 9MM.

    Leading can be caused by oversized throats in a revolver, too soft an alloy, too hard an alloy, to little lube, etc. Where the leading is in the barrel gives us a very good idea what is causing the leading. We can then make adjustments. Lead bullets can be shot in almost all applications with little or no leading with some research and work.

    CastBoolits.com is often recommended here for great info on shooting lead bullets.
     
  15. xsquidgator

    xsquidgator Member

    Joined:
    Jan 14, 2007
    Messages:
    836
    Just got going this morning, thanks everyone for the guiding questions. It's a little embarrassing but I didn't know to ask any of this stuff when I ordered, I incorrectly assumed all lead bullets came sized and lubed like the ones in the box that my friend lent me. I ordered these from Midsouth Shooter's Supply over the internet, simply because they had lead bullets in stock and no-one else seemed to have what I wanted in stock (I have jacketed bullets in 38 and 9mm on backorder from Cabelas).

    The 38 bullets are Hornady 158gr .358" SWC, and I don't see anything on the box label that indicates cast or swaged. The bullets are a dull lightish gray in color and appear to be coated with a powderish finish that's loose inside the box.

    The 9mm bullets are Speer .356" 125gr round nose, and are dark gray in color like a pencil lead, and very smooth even slick to the touch. Again, no info that I can see anyway on the label to indicate whether cast or swaged.

    Does either of these appearances (powderish finish and light gray, or dark gray lead color and very slick) say anything significant?

    The loaner bullets I'd started with are 38 148gr SWC (button nosed) that came lubed, and other than being a little sticky with the lube on them they were a plain lead color, not as dark as the Speer. Neither of these guys that I bought of the Hornady or the Speers looks like these.
     
  16. cdrt

    cdrt Member

    Joined:
    Mar 12, 2007
    Messages:
    949
    Location:
    The Lone Star State
    Sent you a PM back. Sounds like you got this all figured out. Now everyone can give you their pet load for these bullets. :)
    I don't load 9mm anymore, but a nice load for the .38 with the 158 SWC is 3.0 grains of Bullseye.

    Navy Vet & SWIFT Boat OIC
     
  17. Walkalong

    Walkalong Moderator

    Joined:
    Nov 20, 2006
    Messages:
    48,436
    Location:
    Alabama
    The Hornady's are lubed. I have no experience with the Speer, but I suspect they are also. :)

    Try 3.3 Grs. Bullseye, 3.5 Grs. 700X, or 4.0 Grs. W231 for around 750 to 825 FPS with the Hornady 158 Gr. bullets. :)
     
  18. Redneck with a 40

    Redneck with a 40 Member

    Joined:
    Jul 26, 2006
    Messages:
    2,273
    +1 on Oregon Trail Lasercast

    +1 on Oregon Trail laser cast, excellent bullets. I have 500 180 grain 40 bullets loaded with 5.1 grains of Unique with CCI 500 primers, this is an excellent load, mild recoil and accurate.:D There is absolutely no leading in the barrel either.
     
  19. BBQJOE

    BBQJOE Member

    Joined:
    Mar 13, 2007
    Messages:
    736
    Location:
    ARIZONA
    Try taking a knife and scraping the bullet. Chances are good that you'll see that there is a coating on the bullet (the gray ones).This is lube coating, no need for any further lubing.
     
  20. xsquidgator

    xsquidgator Member

    Joined:
    Jan 14, 2007
    Messages:
    836
    I made a box of 50 9mm's today (3.9 grains of Unique) using the 125 grain Speer lead round nose bullets and CCI primers. I'll try them out tomorrow and see how they do especially with respect to leading.
     
  21. CZ57

    CZ57 member

    Joined:
    Jan 6, 2005
    Messages:
    1,533
    Location:
    Heart of Texas
    If memory serves, the Hornady .358" swaged bullet has knurling on its shank and are not lubed, but coated as BBQJOE pointed out. I think the SPEER is swaged also. I haven't used them in a long time and they were when I did. Maybe someone will have more up to date info. But, if you have a SPEER manual, there is load data in it for their bullet. If you're going to use W-231 here also, the load range for the 125 is 3.8 (911 fps) - 4.1 (982 fps) velocities were from a Beretta with a 4.9" barrel. ;)
     
  22. xsquidgator

    xsquidgator Member

    Joined:
    Jan 14, 2007
    Messages:
    836
    Ah, they must have been lubed as several people here were kind enough to tell me. I shot the 50 9mms through 3 different pistols, probably about 30 of them through a Kahr CW9, and didn't see any signs of leading that I could tell when I stripped the pistol down afterwards. Just to be sure I then shot one or two magazines of FMJ through to try and clear it out, but the bore still looked about the same to me. Maybe some little grains of powder in the bore, but it all came out easily.

    The one thing I did learn was the 3.7 gr of Unique isn't quite enough for 125 gr LRN in a 9mm semi-auto. Had one or two FTF and FTE jams, and on all 3 pistols there wasn't quite enough "umph" in the load to make the slide go all the way back - the slides on all pistols generally did not lock back on the last round as they do with the store bought 9mm.

    Since the next disk hole size on my Lee Auto-powder loader is 4.4 grains when I measure it, I'll do that and see how it works even though 4.4 is near max loads per one of my manuals. I also today ordered one of those more precise dedicated powder loaders and an electronic scale. For pistol anyway I think I really need the ability to control the amount of powder more finely than in increments of 3.7 grains or 4.4 grains.
     
  23. BAGTIC

    BAGTIC Member

    Joined:
    May 19, 2007
    Messages:
    26
    Location:
    MISSOURI
    I bought a thousand Speer swaged bullets many years ago. NEVER AGAIN. Even with a light target load they plastered the last three inches of rifling in my 6" revolver so that I couldn't see the riflings and grooves.
     
Thread Status:
Not open for further replies.

Share This Page