Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Nylon 66 help

Discussion in 'Rifle Country' started by Rupestris, Jan 6, 2003.

Thread Status:
Not open for further replies.
  1. Rupestris

    Rupestris Member

    Joined:
    Jan 6, 2003
    Messages:
    1,589
    Location:
    SE Michigan
    Hello all.
    I have a Remington Nylon 66 that I am trying to determine the date of production on. The letter code of the barrel shows that it is either Oct. 1964 or Feb 1973. I know that 66's built before 1968 have no serial number. My question is: Where would I find the serial number on a 66? I've taken off the barrel and receiver cover and the barrel is not stamped with anything that resembles a SN and the only number I can find is printed, not stamped, on the left side of the plastic stock/reciever housing in yellow ink. Is this the SN or is this a pre '68 production? Do I need to further disassemble a 66 to find a SN?

    Thanks for any help. It'll be interesting (to me anyway) if this .22 turns out to be older than me and is in better shape.:D

    Rupe
     
  2. Gordon

    Gordon Member

    Joined:
    Dec 26, 2002
    Messages:
    8,110
    Location:
    central Kali.
    I just read this post and I like Nylon 66's I have no idea and dont care where serial number is but PLEASE DONT FURTHER DISASSEMBLE GUN. This is the hardest gun to put back together Ive ever seen. Even harder than a 742 Remington. I think you just were supposed to remove reciever cover and blow off dirt gently with air. Clean bolt face with A LITTLE solvent on tooth brush and use pin oiler on steel parts. Nobody likes to put these back together you will have a box of useless parts.:what:
     
  3. Rupestris

    Rupestris Member

    Joined:
    Jan 6, 2003
    Messages:
    1,589
    Location:
    SE Michigan
    Thanks Gordon.
    That is exactly why I didn't go further than the cover and bbl. I'm curious but not that curious. I have no intention of getting rid of this piece so the date is just for my own general knowledge and so when my son takes ownership he can tell his kids how old it is.

    Rupe
     
  4. Bottom Gun

    Bottom Gun Member

    Joined:
    Dec 26, 2002
    Messages:
    766
    Location:
    Elgin, Arizona
    Rupestris,

    You have fine rifle. I've been shooting them since the 60's and have owned 8 of them. I think they are some of the finest .22 rifles ever made.
    Don't be intimidated by the innards of these things they really aren't that difficult to assemble again once you have them apart.

    My suggestion is to keep it dry. They were designed to function without oil so the less you use, the cleaner it'll stay. I spray the internal metal parts of mine with Remington dry lube to keep them rust free. If you'll do that, you'll only have to wipe down the outside periodically with an oily rag to stop corrosion.

    Yours is a pre 1968. Some of the serial numbers were located on the side of the receiver cover and others were marked on the underside of the barrel forward of the stock.

    You can determine the date of manufacture from the letter code stamped on the barrel.
    Here's a web site where you can find that information along with some history of the rifles and an exploded parts drawing to help you with disassembly and assembly should you decide to.

    http://groups.yahoo.com/group/nylonrifles/files/

    Check it out. I think you'll find it's quite interesting and a wealth of information.

    Hope that helps,

    Ken

    PS: Which model do you have?
     
  5. Hemicuda

    Hemicuda member

    Joined:
    Dec 26, 2002
    Messages:
    1,064
    Location:
    Middle of the Mitten!, Michigan
    I got 3 of these guns... WONDERFUL little rifles...I once totally dissasembled one of mine... (the first one, YEARS ago, before the internet, and you guys wealth of info)

    I am happy to report that it IS still functioning... (bolt and hammer removal ain't too bad, when you figure out the tricks)

    as for production dates... dunno... Harley Nolden (on this forum) might be able to help)

    the ONE I have that has a serial # on it has it stamped on the bottom of the barrel, just ahead of the forend...

    also, I have a "Kasnar" Brazilian copy of the Nylon 66... (OBVIOUSLY made with the same machines and whatnot, as ALL parts seem to be interchangable with the real thing...
     
  6. Jagermeister

    Jagermeister Moderator In Memoriam

    Joined:
    Dec 23, 2002
    Messages:
    371
    Location:
    Brunswick GA
    Rupestis:
    I have the complete disassem of you 66, w/photos. If you'd like to have them send me an email addy

    JM
     
  7. Bottom Gun

    Bottom Gun Member

    Joined:
    Dec 26, 2002
    Messages:
    766
    Location:
    Elgin, Arizona
    You guys can get production dates from the link I posted earlier. They list all the mfg codes ever used.
     
  8. Rupestris

    Rupestris Member

    Joined:
    Jan 6, 2003
    Messages:
    1,589
    Location:
    SE Michigan
    Thanks for all the help everyone. The 66 is now clean, and re-assembled.

    Bottom Gun, Thanks for the link. There is a wealth of info on the nylon guns there (confirmed date- Oct. 1964). As for mine, its a standard Nylon 66 - brown/white diamond. It is in excellent condition having been in a safe for most of its life. In no way does it look as old as it is.

    Now, I hope no one recommends that I put it up and never shoot it again.:D

    Hemicuda, will we see ya on Woodward this year?:cool:

    Rupe
     
  9. Bottom Gun

    Bottom Gun Member

    Joined:
    Dec 26, 2002
    Messages:
    766
    Location:
    Elgin, Arizona
    Rupe,

    Glad that info was helpful to you.

    Shoot the heck out of it and enjoy it. You'll be surprised at its accuracy.
    I have a couple of the Apache black ones and I love them.

    Make sure you wipe down the exterior after handling it. That blued steel seems to rust rather easily.
     
  10. rokqtmn

    rokqtmn Member

    Joined:
    Oct 7, 2009
    Messages:
    1
    Gordon- go to NYLONRIFLES.COM dedicated to Nylon 66- has excellent easy to do video on assembly and disassembly. All very simple- the caveat everyone is talking about is the trigger assembly. Lots of little flat springs. This you leave alone.
     
  11. AStone

    AStone Member

    Joined:
    Aug 5, 2005
    Messages:
    24,176
    Location:
    Far N, E coast
    Wow, do I ever regret selling mine during grad school (so I could eat).

    It was my first real rifle (beyond pellet gun). Loved it.
     
  12. CZguy

    CZguy Member

    Joined:
    Mar 25, 2004
    Messages:
    3,975
    Location:
    Missouri
    Heck no, but I do recommend that you sell it to me. :D
     
  13. TehK1w1

    TehK1w1 Member

    Joined:
    May 21, 2007
    Messages:
    869
    Location:
    Where the Wild Things Are
    I don't recommend putting it up forever. I do recommend not trying to take it apart to clean it unless you are handy with tools and have a detailed set of instructions.
     
  14. krs

    krs Member

    Joined:
    Jan 16, 2006
    Messages:
    2,588
    Location:
    Tall Trees
    Rupestris,

    I'm sure you helped the OP a great deal.........if he's still alive.

    This thread is over six years old:rolleyes:
     
Thread Status:
Not open for further replies.

Share This Page