Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

[Pics] S&W Model 34 pics...and need advice.

Discussion in 'Handguns: Revolvers' started by NCBeagle, Aug 2, 2008.

Thread Status:
Not open for further replies.
  1. NCBeagle

    NCBeagle Member

    Joined:
    Apr 13, 2008
    Messages:
    69
    Location:
    Charlotte, NC
    Posted 02 August 2008 10:30 PM
    I have quite a few J-frames and bought a Model 34 for cheap practice with the trigger pull. This is to share pictures of the great Model 34-2 I purchased this weekend (see below)and also to ask advice. This is my first 22 lr revolver.

    I bought the gun, gave it a cursory cleaning, and then put approximately 300 rounds down range. Afterward, the barrel was quite fouled with lead and so filthy that it was hard to run a copper brush through. Should I give it a quick brush out every 100 rounds or so? What do you usually do? I clean my .38, 9mm and .45s more more or less often, but usually shoot copper jacketed rounds.

    After how many rounds do you clean your 22 lr revolvers? Any tips? It was quite difficult to clean the lead out of this barrel. That aside, this gun is great fun...I could shoot it all day.

    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
     
  2. Shear_stress

    Shear_stress Member

    Joined:
    Apr 27, 2005
    Messages:
    2,728
    Now that is a wonderful little wheelgun. Thanks for sharing the pictures.

    As for cleaning, I'm of the mind that the less, the better. I would run a bore snake, rather than cleaning rod, through the barrel and chambers only when leading gets to be a problem (accuracy degradation, tough extraction). You might switch to plated bullets as that will reduce barrel leading.
     
  3. NCBeagle

    NCBeagle Member

    Joined:
    Apr 13, 2008
    Messages:
    69
    Location:
    Charlotte, NC
    Shear_stress,

    I absolutely agree that less scrubbing is better. I could not even get a bore snake (the copper tip of the rope) down the barrel after 300 rounds. The chambers and forcing cone were clean. I plan to shoot this little gun a lot...that's how I justified the purchase;) It sounds like I need to run the snake every 50 rounds or buy jacketed rounds, or both.
     
  4. JERRY

    JERRY Member

    Joined:
    Jun 5, 2003
    Messages:
    2,349
    you gun is clearly defective and i'll offer you $200.00 plus actual shipping, just so youre not stuck with a bad gun....'cause we're all buddies here and all.....
     
  5. Ala Dan

    Ala Dan Member in memoriam

    Joined:
    Dec 24, 2002
    Messages:
    12,879
    Location:
    Home Of The First Capitol Of The Confederate State
    I've got a pristine, factory nickel 2" square butt S&W model
    34-1 .22 caliber LR. Sorry, its 0340 hrs as I write this; and I
    can't awaken the household in order too take pic's~! :uhoh: ;)

    FWIW, I can't give any advice as too ammo choice; for I don't
    (and won't) ever shoot this firearm, as it joins several other J-
    frame S&W's as "SAFE QUEENS".
     
    Last edited: Aug 3, 2008
  6. mnrivrat

    mnrivrat Member

    Joined:
    Dec 24, 2002
    Messages:
    4,612
    Location:
    MN
    You might try a different brand of ammo. I had this same problem with Remington bulk pack on my .22 revolver (just in case your shooting them).

    The lead apparently was soft on the ones I had and leading was what I would call severe and pre-mature. Other brands may have harder lead and not foul the bore so quickly.

    On the ones I mention I would get notable leading within 50 rounds and needed to clean it. Problem solved with different ammo.
     
  7. XavierBreath

    XavierBreath Member

    Joined:
    Jan 6, 2003
    Messages:
    5,054
    Location:
    Louisiana
    I agree, try a different ammunition.
     
  8. NCBeagle

    NCBeagle Member

    Joined:
    Apr 13, 2008
    Messages:
    69
    Location:
    Charlotte, NC
    I appreciate the replies. It sounds like it may be the ammo. I fired about 100 Winchester white box and 200 Remington bulk hollow points.
     
  9. LA Rondo

    LA Rondo Member

    Joined:
    May 23, 2008
    Messages:
    65
    Location:
    Los Angeles, California
    double post, sorry.
     
  10. LA Rondo

    LA Rondo Member

    Joined:
    May 23, 2008
    Messages:
    65
    Location:
    Los Angeles, California
    Chiming into this right here.

    I just got my hands on this little puppy ...


    [​IMG][/IMG]

    For which I purchased this Rem ammo, 2x 500 rounds, ofcourse very cheap :)

    [​IMG][/IMG]

    I suppose, it will create the same kind of residue as described above.
    I haven't had a chance to shoot it yet.

    Well, I may have to look into some brushing, or better go and try to return the ammo? May not be possible ...

    What's a recommended ammo to shoot cleaner?

    Edit:

    I just became obvious. I checked in the safe and found a couple of boxes American Eagle which I got from the seller. Those are copper plated.

    On the Remington I can groove the lead bullet with my finger nail easily, that's how soft it is. The AE ammo is hard covered at the bullet and no way to groove or scratch off the lead the same way ....

    Thanks for the heads up, always something to learn here. I will try and make an exchange @ Big 5.
     
Thread Status:
Not open for further replies.

Share This Page