Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Pillar & Glass Bedding

Discussion in 'Gunsmithing and Repairs' started by whubbard, Feb 9, 2012.

Thread Status:
Not open for further replies.
  1. whubbard

    whubbard Member

    Joined:
    Dec 11, 2011
    Messages:
    59
    Hi,

    I am getting a Richard Microfit Gunstock for my Savage MKII. I am planning on both pillar and glass bedding the rifle stock, beyond that I will have to obviously finish the rifle stock.

    In what order would you recommend I do things?
    My best guess: Finish, Pillar, Glass

    Thanks!

    EDIT: Also, if you any of you know of good internet guides for glass and pillar bedding please let me know. I've found some good ones, but I'm sure there is more out there.
     
  2. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    Pillar bedding & glass bedding go hand and hand, and you do them both at pretty much the same time.
    The pillars are glassed into the stock..

    And you should do all that and final cleanup & sanding before finishing.

    Unless you want to refinish, after you get glass bedding drips and sticky finger prints all over the finish.

    rc
     
  3. stan rose

    stan rose Member

    Joined:
    Oct 21, 2010
    Messages:
    466
    Location:
    New York
    +1 on bedding then finishing, I made the exact mistake rcmodel is talking about with a 1903 stock. I finished it, decided to bed it thought I did a great job on the prep, ...., I did not. You live and you learn.
     
  4. Clark

    Clark Member

    Joined:
    Jan 3, 2003
    Messages:
    4,287
    Location:
    Where I5 meets the rain forest
    I often do not bother to glass bed 223 rifles.

    I do glass bed hard kicking rifles, but it never seems to make them any more accurate.
    Glass bedding poorly can cause accuracy to be much worse.
    So I have got some great gains from glass bedding when someone else had already done it so wrong that there was a long bind on the barreled action.

    I pillar bed Rem700 front and rear.
    I pillar Mauser at least in the rear, and sometimes in the front.

    Almost certainly no more accuracy will be measured, you and I will do it anyway, but here are the links.

    http://riflestocks.tripod.com/bedding.html
    http://www.charm.net/~kmarsh/glasbed.html
    http://yarchive.net/gun/rifle/pillar_bedding.html
    http://www.gun-tests.com/performance/nov96beddingjob.html
    http://www.ranchtrippin.com/bedding/
    http://www.scorehi.com/main.htm
    http://www.6mmbr.com/pillarbedding.html
    http://www.brownells.com/aspx/NS/Store/ProductDetail.aspx?p=9899
    http://www.brownells.com/aspx/ns/store/catSearch.aspx?c=1418
    http://www.z-hat.com/Accurate.htm
    http://www272.pair.com/stevewag/mmrifle/mmrifle3.html
    http://www272.pair.com/stevewag/turk/turkbed1.html
    http://www272.pair.com/stevewag/turk/turkbed2.html
    http://www272.pair.com/stevewag/turk/turkbed3.html
    http://yarchive.net/gun/rifle/remington700.html
     
Thread Status:
Not open for further replies.

Share This Page