Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Pre-Priming Brass?

Discussion in 'Handloading and Reloading' started by woolfam, Jan 8, 2006.

Thread Status:
Not open for further replies.
  1. woolfam

    woolfam Member

    Joined:
    Jun 17, 2003
    Messages:
    163
    Location:
    KC MO
    I reload 9mm, not so much because it is economical to so, but because I enjoy doing it. I usually prep about 200 - 250 cases at a time (polish, deprime & resize, and bell & deburr the case mouth). I keep the prep'd cases in plastic bags. Can I include priming the cases in my prep routine? Would priming the cases and then storing them in the plastic bags possibly affect the performance of the primers? I usually finish loading the rounds w/in a month or two but I've worried that storing unfinished / primered rounds might degrade the powder in the primer.

    Anyone have any experience with this?
     
  2. P95Carry

    P95Carry Moderator Emeritus

    Joined:
    Jan 3, 2003
    Messages:
    16,341
    Location:
    South PA, and a bit West of center!
    IMO - zero concerns at all.

    If primers are stored in good environment anyways - and primed cases in same - no difference! I will assume here average temperatures and fairly low humidity - but primers in boxes or cartridge cases - no difference in longevity.

    For me - not an issue.
     
  3. R.W.Dale

    R.W.Dale Member

    Joined:
    Oct 14, 2005
    Messages:
    11,398
    Location:
    Northwest Arkansas
    I doubt it would have much of an ill effect. Just search up how hard it is to "Kill" primers on pourpose.
    I loaded some 7.62x45r brass yesterday that had been primed 3 or 4 years previously shot just fine. It's not like the little boxes primers come in are sealed in any way.
     
  4. ClarkEMyers

    ClarkEMyers Member

    Joined:
    Oct 3, 2003
    Messages:
    931
    Location:
    A stone's throw from Henry's Fork
    factories sell primed brass and it works - likely they know what they're doing

    Factories sell primed brass and it works - likely they know what they're doing. I have Winchester primed brass that I bought that way in plastic bags same as the unprimed brass that I bought that way.

    If it doesn't work I have lots of expert company.
     
  5. theCZ

    theCZ Member

    Joined:
    Nov 3, 2003
    Messages:
    808
    Location:
    Nevada
    I store my primed 9mm cases in a coffee can, and I've had zero primer failures in 6000 rounds that I've loaded in the past few years. Same for rifles but on a smaller scale.
     
  6. tbeb

    tbeb Member

    Joined:
    Dec 30, 2002
    Messages:
    852
    Location:
    Northwest Indiana
    I've always primed cases and set them aside until I did some reloading. I keep some in plastic ammo boxes and others in boxes that factory ammo comes in, in my basement which is a cool, dry place. I've been reloading a long time, and never had any ignition problems.
     
  7. woolfam

    woolfam Member

    Joined:
    Jun 17, 2003
    Messages:
    163
    Location:
    KC MO
    Thanks for taking the time to respond. I had not thought about the fact that primed brass is sold. And I would keep the primed brass in the same environment as I do the primers themselves. And your are right, the primers themselves are not in sealed packages.

    And now if you'll excuse me, I've got about 700 pieces of brass to prime. :)
     
  8. JDGray

    JDGray Member

    Joined:
    Sep 16, 2005
    Messages:
    5,131
    Location:
    SW MI.
    Even after getting a turret press, I still like sizing and depriming on my single stage. I always keep 300-400 hundred cases primed and read to load. JDGray
     
  9. Rockstar

    Rockstar member

    Joined:
    Apr 25, 2004
    Messages:
    1,353
    You don't need to debur straightwall handgun cases. If you're loading on a progessive, all you need to do is tumble them, then run them through your press.
     
  10. armoredman

    armoredman Member

    Joined:
    Nov 19, 2003
    Messages:
    16,765
    Location:
    proud to be in AZ
    All I do with my 9mm cases is tumble, decap/resize, inspect, tumble, and then prime. I try to keep as much preprimed on hand as I can. I use the belling die to hold the powder measure on the press, so I bell, then charge.
    Using a single stage, doing the priming ahead of time can be a real time saver.:p
    Thanks for reminding me - I still have 80 to do, then buy more primers....
     
  11. rick_reno

    rick_reno member

    Joined:
    Dec 25, 2002
    Messages:
    3,027
    You'll be fine priming your cases - don't worry about it.
     
  12. pcf

    pcf Member

    Joined:
    May 5, 2003
    Messages:
    862
    Location:
    Arlington, TX
    I've done informal testing with primers and solvents. If you soak them for extended periods of time (several days) in solvents or pentrating oil, it can affect their reliability.

    If you soak loaded ammunition in solvents, oils, or water, you should be more concerned about the liquids contaminating the powder than affecting the primers.

    Even if you manage to "kill" the primers with water, or a light oil or solvent, they will work again after they dry out.

    Overall, there's no need to be concerned.
     
  13. Matt G

    Matt G Moderator Emeritus

    Joined:
    Dec 21, 2002
    Messages:
    3,547
    Location:
    N. TX
    I've pre-primed many times, meaning to get back to the cases within a matter of days or weeks. As life goes, it sometimes turns into YEARS.

    Zero problems thus far even with rifle accuracy.
     
  14. birddog

    birddog Member

    Joined:
    Oct 2, 2003
    Messages:
    1,049
    Location:
    Western NY state
    I always preprime brass. Makes the final loading on my Lee Turret that much quicker. Never had any problems, even after letting the primed cases sit for months, or a year.
     
  15. The Bushmaster

    The Bushmaster Member

    Joined:
    Jan 29, 2005
    Messages:
    7,872
    Location:
    Ava, Missouri
    Well I guess you got your answer...Prime-em and store-em in a cool dry dark place...:cool:
     
  16. woolfam

    woolfam Member

    Joined:
    Jun 17, 2003
    Messages:
    163
    Location:
    KC MO
    I've received my answer and more! Thanks again, everyone, for the information. Interesting! The collective experience of the Borg is an abundant resource.
     
  17. Unisaw

    Unisaw Member

    Joined:
    Dec 28, 2002
    Messages:
    780
    Location:
    Pacific NW
    I pre-prime all of the time. As a matter of fact, I finished some reloads the other night that records indicate were primed in 2002. I guess I'm not shooting enough!
     
  18. Sam Adams

    Sam Adams Member

    Joined:
    Jan 28, 2003
    Messages:
    2,035
    Location:
    South Texas
    I've got LOTS of pre-primed brass. I specifically bought a Lee hand press to be able to deprime/size and then bell handgun cases while sitting in front of the TV, pretending to watch some stupid chick flick with SWMBO. I'll usually prime after she's gone to sleep, while watching Mail Call or something else worthwhile.

    You know those barrels of pretzels that you can get at Sam's (2 1/2 pounds or so of pretzels)? They are great for case storage - I've got over 2,000 9 mm cases (primed and ready to be charged and loaded) in one and roughly 1,500 of .45 (with some more room left) in another.
     
  19. trickyasafox

    trickyasafox Member

    Joined:
    Dec 22, 2004
    Messages:
    2,523
    Location:
    upstate NY go to school in WNY
    i pre prime all my rifle brass and have never encountered an accuracy or function problem :)
     
Thread Status:
Not open for further replies.

Share This Page