Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Primer only

Discussion in 'Handloading and Reloading' started by jeff-portnoy, Oct 6, 2012.

Thread Status:
Not open for further replies.
  1. jeff-portnoy

    jeff-portnoy Member

    Joined:
    Sep 15, 2012
    Messages:
    43
    Location:
    Boston, MA
    Hi guys.
    Please, tell me what happens if load primer only in 9x19 cartridge? (115,125gr bullet)
    I mean how much f.p.s , pressure, etc.
     
  2. bds

    bds Member

    Joined:
    Jan 10, 2010
    Messages:
    14,006
    Location:
    Northwest Coast
    For me in 9mm (also for 40S&W/45ACP), regardless whether 115/124/125 gr bullets, primer only resulted in squib loads where the bullet was stuck in the barrel right by the chamber or a little down the barrel depending on the bullet type. So, zero fps as the bullet never exited the barrel.

    But primer can propel glue stick bullets enough to punch through card board boxes. :D

    Glue stick 45ACP bullets - http://www.youtube.com/watch?v=20Px6Vz8tt8

    Glue stick bullets using bullet molds - http://www.youtube.com/watch?v=3kwv8sZxdtc
     
  3. james layman

    james layman Member

    Joined:
    Jan 1, 2012
    Messages:
    54
    Location:
    Purcellville, Va.
    From my experience, I would not try it. I saw a 6.5 Jap rifle bullet that got stuck in the barrel. James
     
  4. FROGO207

    FROGO207 Member

    Joined:
    Dec 7, 2008
    Messages:
    6,352
    Location:
    Mount Desert Island Maine
    As I have moved through the reloading experience I find that the primer alone with glue sticks, various plastic/rubber, and wooden bullets that do not take the force to engrave the rifling and overcome the bore friction MAY work with just a primer but I have had zero success with that happening when using lead or jacketed bullets. If you try it yourself plan on driving a lot of bullets out of the barrel before you give up.:) I do however load light loads that will just exit the barrel with minimal velocity and stick in a couple layers of cardboard sometimes though this light of a load is not always predictable either.
     
    Last edited: Oct 8, 2012
  5. Walkalong

    Walkalong Moderator

    Joined:
    Nov 20, 2006
    Messages:
    47,107
    Location:
    Alabama
    A primer only will not propel any normal lead, plated, or jacketed bullet through the barrel.
     
  6. Certaindeaf

    Certaindeaf member

    Joined:
    Jan 16, 2012
    Messages:
    5,170
    Location:
    Wet Oregon
    Certain primers MAY make a lubed pure lead ball leave the barrel with varying levels of "performance". It all depends..
    If you try it, check your bore after each shot and make sure you have a good rod and mallet handy.
     
  7. rsrocket1

    rsrocket1 Member

    Joined:
    May 20, 2010
    Messages:
    1,286
    Location:
    Sacramento, CA
    One primer only bullet got out of my 4" Ruger Service Six. A 158g LRN Silver State Hardcast. 231 fps.

    Have had a couple of my own cast Lee 158g RNF fire with a primer only. They got stuck in the forcing cone. A couple of taps with a brass rod and hammer put it back into the cylinder and back into the case (you have to drive it back out from the front end unlike an autoloader). No harm, no foul.

    I do shoot glue stick bullets with primers. You need to lube them and seat them at the bottom of the case. They come out pretty fast and will go right through a cardboard box :). If you are going to try primer only, be sure to do it outdoors, the smoke is filled with lead from the Lead Styphnate primer compound.
     
  8. Certaindeaf

    Certaindeaf member

    Joined:
    Jan 16, 2012
    Messages:
    5,170
    Location:
    Wet Oregon
    I used to use paraffin and those Speer? plastic slugs. pretty fun for whacking stuff
     
  9. mdi

    mdi Member

    Joined:
    Dec 31, 2007
    Messages:
    1,952
    Location:
    Orygun!
    I don't recommend it, but, some have been known to slug their barrel using primer only loads. "Fire" the bullet up into the bbl, and drive it back out. Measure for groove diameter...
     
  10. 45lcshooter

    45lcshooter Member

    Joined:
    Oct 6, 2012
    Messages:
    919
    Location:
    Central of the Commonwealth of PA
    I never heard of glue stick bullet. Any real use for it? Other than non lethal gun fire, or tick of the neighbors?
     
  11. tightgroup tiger

    tightgroup tiger Member

    Joined:
    Mar 20, 2011
    Messages:
    2,178
    Location:
    Peidmont/Triad, NC
    possums don't like them either.
     
  12. W.E.G.

    W.E.G. Member

    Joined:
    Sep 26, 2006
    Messages:
    7,395
    Location:
    all over Virginia
    Does the person who put you up to this also let the air out of your tires and pour water on your front porch in freezing weather?
     
  13. gamestalker

    gamestalker member

    Joined:
    Sep 10, 2008
    Messages:
    9,832
    Location:
    SW Arizona
    I tried using s primer only in my G17 way back in the 1980's and all they did was stick the bullet in the barrel. But I did come up with some good wax / tissue paper loads using just primers in 38 spcl that were fun to goof off with. And back in the 1960's I used to pull bullets from 22 lr and then dump the powdder out then stuff them with waxed Q tip ends. Those were a ton of fun to shoot in my house at a card board box target.


    GS
     
  14. kingcheese

    kingcheese Member

    Joined:
    Nov 29, 2008
    Messages:
    677
    I tried it in a nagant revolver with 17g plastic bullets, got stuck on the barrel
     
Thread Status:
Not open for further replies.

Share This Page