Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Question concerning light BE-86 load in 44 mag

Discussion in 'Handloading and Reloading' started by gonoles_1980, May 16, 2015.

Thread Status:
Not open for further replies.
  1. gonoles_1980

    gonoles_1980 Member

    Joined:
    Jun 29, 2013
    Messages:
    1,005
    Using a Speer LSCW 240 grain bullet.

    As I have mentioned before on here, I misread the online alliant page and ended up loading 8.1 grains of BE-86. I have written alliant about it and the response I get is understandable from a legal sense, they say don't go below 10% of the top end load which is 11.8grains Obviously my 8.1gr is well below the the 10.6 low end.

    So I fired 48 of the 100 I made after my ladder load today, and I kinda like it as a light plinking load. What to do, should I go ahead and jump to 10.6 grains for my light load, or stick with this level since I kinda like it?

    Anyone have experience light loading BE-86, if they have been firing ok, any reason I shouldn't continue to use it, I could bump up some without an issue?
     
  2. Walkalong

    Walkalong Moderator

    Joined:
    Nov 20, 2006
    Messages:
    48,380
    Location:
    Alabama
    Test it out powder forward to make sure it does well no matter where it is in the case. If it does well, you may be OK. Many powders are loaded to less than 10% of max with no troubles. Time will tell about BE-86.
     
  3. gonoles_1980

    gonoles_1980 Member

    Joined:
    Jun 29, 2013
    Messages:
    1,005
    I load the cylinder with the gun pointed down at about a 45 degree angle, so the bullet is downward somewhat. Is that enough to get the powder to go forward, or should I hold the bullet upside down, then load? I fire level since it has a concrete floor and I don't want to hit the floor.
     
  4. Walkalong

    Walkalong Moderator

    Joined:
    Nov 20, 2006
    Messages:
    48,380
    Location:
    Alabama
    Load normally. Before each shot, first let the barrel point straight down, then slowly bring it up level and shoot. Reverse for testing powder back. It won't be all forward or all back either way, but we don't want to shoot the concrete, nor any passing planes. :)
     
  5. gamestalker

    gamestalker member

    Joined:
    Sep 10, 2008
    Messages:
    9,832
    Location:
    SW Arizona
    I've tested as Walkalong described, it provided enough position variation to make a reasonable conclusion.

    There's another thread going right now about 32-20 with position sensitivity issues, in that thread the OP is thinking about using styro to help keep the powder against the flash hole, which sounds like a pretty effective method. I've used dacron before, and it worked well also.

    As to your charge, I would probably run them across the chrony if you have one. If they're pretty consistent fps, and considering you've already shot almost half of the batch, I would think you should be alright in shooting the rest of the 8.1 gr. charges. Just make sure all of them clear the barrel and you should be fine, IMO.

    GS
     
  6. Wreck-n-Crew
    • Contributing Member

    Wreck-n-Crew Member

    Joined:
    Jan 15, 2014
    Messages:
    1,189
    Location:
    ohio
    I have a light plinking load for 44 mag using Unique. It is above 44 special and below 44 magnum. Makes a nice plinking round and I enjoy it. Not sure how accurate it is yet...going for accuracy with those loads tomorrow.

    Testing some Power Pistol 44 special and 44 Magnum loads tomorrow. Let you know how it goes.

    NO PLINKING LOADS FOR ME USING 296/H110. It drops off way too easy!
     
  7. gonoles_1980

    gonoles_1980 Member

    Joined:
    Jun 29, 2013
    Messages:
    1,005
    Thanks guys, I will do the pointing method before firing to test. I think my next load I will just go to 9.0, still below minimum, but I know 7.9-8.3 will fire from my test loads. I've got a heavier load I use with 11.3 BE-86 with xtreme 240gr copper plated.
     
Thread Status:
Not open for further replies.

Share This Page