Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Question on load data..

Discussion in 'Handloading and Reloading' started by scythefwd, Sep 29, 2012.

Thread Status:
Not open for further replies.
  1. scythefwd

    scythefwd Member

    Joined:
    Mar 13, 2008
    Messages:
    3,597
    Location:
    Manassas Park, VA
    WT Bullet MFR Powder Dia COL Start VEL Max VEL
    165 GR. SIE SPBT Hodgdon H4895 .308" 3.300" 43.0 2607 47.5 2782



    OK, according to this load data, directly off of hodgdons site The recipe is:
    165 Sierra Game king,
    43 gr. H4895
    Expected velocity of 2600 fps

    and here is the question

    Is that COL for the max load or the minimum? My chamber is tight and wont support that coal.. max of 2.672 for that bullet in my chamber..
     
  2. JLDickmon

    JLDickmon Member

    Joined:
    Mar 15, 2012
    Messages:
    665
    Location:
    Comstock, MI
    the real answer is the COAL really depends on two things.. the ogive of the bullet, and the magazine.

    You could conceivably have two bullets, both the same weight, seated to the same COAL, one would chamber but the other will not because one bullet is fatter further towards the tip.

    The other would be, how much room in the magazine you have. Too long of a COAL will not allow the cartridge to fit in the mag well.

    Soooooo.. your solution would be; You know what the OAL needs to be to function in the rifle. So back the data off 10% to start with, and work the load up from there until the rifle likes it.
     
  3. 243winxb

    243winxb Member

    Joined:
    Jul 7, 2004
    Messages:
    9,392
    Location:
    Hopewell Big Woods
    This is 30-06 3.300" Load data looks like 308 ??????????????????
     
  4. SpringfieldM1A

    SpringfieldM1A Member

    Joined:
    Sep 16, 2010
    Messages:
    58
    243winxb is right you have load data for 30-06 but your measurement for your chamber sounds like 308?

    The cartridges are next to each other maybe clicked the wrong one?

    COAL for .308 is 2.75"
     
  5. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    I agree you are using 30-06 Starting load data.
    Hopefully that is what you are trying to reload?

    Neither one.
    It is the COL the data was tested at in Hodgdons pressure test barrel.

    You can go in or out, up or down, or whatever.

    Thats why you always start at the recommended Starting load, and work up in YOUR rifle.

    At the suggested starting load you are using, seating depth has no bearing on pressure or safety.

    Gofer It!
    If you are loading for a 30-06?

    rc
     
  6. scythefwd

    scythefwd Member

    Joined:
    Mar 13, 2008
    Messages:
    3,597
    Location:
    Manassas Park, VA
    243 and others..

    43gr is the starter for the 30-06 using H4895. Both my Lee manual and the Hodgdon website confirm this. They both also list 3.30" as the lenght.. which is why I was so confused.

    THis does overlap with .308 win, where 43.5 is max (in standard brass.. you run 43 in the LC match I use and you're running compressed loads).
     
  7. 243winxb

    243winxb Member

    Joined:
    Jul 7, 2004
    Messages:
    9,392
    Location:
    Hopewell Big Woods
  8. scythefwd

    scythefwd Member

    Joined:
    Mar 13, 2008
    Messages:
    3,597
    Location:
    Manassas Park, VA
    thanks guys.. Felt that was the answer... but I figured it couldnt hurt to ask.
     
  9. gamestalker

    gamestalker member

    Joined:
    Sep 10, 2008
    Messages:
    9,832
    Location:
    SW Arizona
    The only time you really need to consider seating depth in regard to it's effect on pressures, is when you get real close to, or are, touching the lands. Handgun pressures are of course a different story, and are very responsive to seating depth variations in most cartridges, especially AL types.

    GS
     
Thread Status:
Not open for further replies.

Share This Page