Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Recommendations for a Powder Measure

Discussion in 'Handloading and Reloading' started by IrvJr, Mar 31, 2007.

Thread Status:
Not open for further replies.
  1. IrvJr

    IrvJr Member

    Joined:
    Jan 6, 2003
    Messages:
    265
    Hi All,

    I recently started reloading,currently only handguns (.44sp/mag, .38sp/.357mag). I've been using a Lee HandPress and only load moderate amounts of ammo. Eventually I might want to invest in a turret press, but for now the hand press works well for me.

    Currently, I use the Lee plastic powder measure dippers to measure my powder. However, I'm in the market for a more convenient way to measure out powder for my loads. The problem that I've found with the Lee plastic dippers is that they are not convenient for loading low volume charges. For example, my loading manual specifies a max of 5.2 grains of Unique for a .38 special load, yet the smallest Lee dipper that I have in my set will measure 2.7 grains per scoop. If I use two scoops with the smallest dipper, I will have measured 5.4 grains of Unique.

    I'd like to find something that would let me safely, accurately and consistently measure these lower powder charges. The dippers are easy to use, and I figure if I use 5.4 grains of Unique, I'm OK since I'm firing the .38 special loads from a .357 mag revolver. However, I'd like to be able to measure lower volume loads of Unique in a consistent, accurate manner.

    I like Lee products - anyone have any feedback on their other powder measurers?
     
  2. scrat

    scrat Member

    Joined:
    Jan 27, 2007
    Messages:
    6,882
    Location:
    Monrovia, CA
    do you have the full set of lee dippers. sounds kinda odd.
    i use the lee dippers, same time though i have a digital scale.
     
  3. lee n. field

    lee n. field Member

    Joined:
    Dec 29, 2002
    Messages:
    3,731
    The RCBS Little Dandy might be good for you.

    Per Midway:
    Exactly that. You don't need to buy the whole set of rotors, just what you need.
     
  4. NailGun

    NailGun Member

    Joined:
    Aug 16, 2006
    Messages:
    274
    Location:
    Gone fishing....
    I just got a new RCBS Uniflow and it works GREAT on Unique. I have a Lee Perfect measure also. It works well on some powders most of the time.

    Check out the Lee Classic Turret press kit at Cabela's. It is inexpensive and works well, and comes with the updated powder measure. I got one not too long ago, and it too works great for 9mm and .38/.357 rounds.

    http://www.cabelas.com/cabelas/en/t...turret&QueryText=lee classic turret&noImage=0

    Check out the video demo at Lee. http://www.leeprecision.com/html/HelpVideos/video.html

    Good Luck, and happy reloading.
    NailGun.
     
  5. benedict1

    benedict1 Member

    Joined:
    Jun 12, 2006
    Messages:
    478
    Location:
    Southern **********
    Here's another option for a Classic Turret kit--I think it is a better deal than other suppliers--you get more stuff, including dies--

    http://www.kempfgunshop.com/products/reloading/leeprecision/kits/KempfKit.html

    I find the Pro Auto Disk Powder measure from Lee to be very accurate for Unique or other flake powders down to about 4 gr. Then they tend to bridge and clump and can cause light charges. You can also get an adjustable charge bar for the Auto Disk and can really dial in a charge--if you want 5.2 gr of Unique then with a little trial and error and weighing the charges you can set it for exactly that.

    The other option is to get the full set of dippers--Kempf has a real good price on them too but I would supplement them with a Lee Safety Scale, which is inexpensive but very accurate, to make sure you are in the ballpark on the charge you want.

    I have a Classic Turret with the Lee Safety Prime and the Pro Auto Disk and wouldn't trade it for any other turret press. It will last a lifetime.
     
  6. Art Eatman

    Art Eatman Administrator Staff Member

    Joined:
    Dec 22, 2002
    Messages:
    43,263
    Location:
    Terlingua, TX; Thomasville,GA
    I use an ancient RCCBS powder measure. Every time I've checked against the scale it's been right on, just as at the last check.

    Art
     
  7. Smokey Joe

    Smokey Joe Member

    Joined:
    Jan 2, 2003
    Messages:
    2,617
    Another option

    Irv Jr--My RCBS Uniflow works great for large powder charges, for rifle reloading. However, when I got into loading for my .357Magnum, for target loads, I found that it had trouble with very small powder charges, like 3.4 grains of W231.

    Fooled around with the RCBS, unsatisfactorily, for a while, until I happened upon a Lyman #50 powder measure which has 3 separate adjustments to its measuring cylinder--Huge, Small, and Really Tiny.

    So, for reloading for target pistol, I use my Lyman #50, and it works really well. Got it used @ a gun show.
     
  8. The Bushmaster

    The Bushmaster Member

    Joined:
    Jan 29, 2005
    Messages:
    7,849
    Location:
    Ava, Missouri
    There is such a wide variaty of ways to measure powder from dippers (I plumb forgot I still have my Lee set of dippers) to elctronic scales that dispense powder onto a scale that I would recommend that you do a bit of research to determine just what you want your scale to do for you. You have dippers, balance beam scales of all kinds and electronic scales by themselves to the dispensing kind. Have fun...And luck...:D

    I have the dippers, a 5-0-5 RCBS beam and a RCBS Powder pro electronic scale. I use the electronic the most...Easier for 64 year old eyes to read and it's quick.
     
  9. IrvJr

    IrvJr Member

    Joined:
    Jan 6, 2003
    Messages:
    265
    Thanks for the many replies fellas. I've only started reloading very recently.

    I'm going to look at the scales and powder dispensers you mentioned.

    I definitley want to move up to a Lee Turret press in the future so that I can have all of my dies installed and set up in the plates. Right now I have to install/uninstall each a die every time I move to a different step in the process.
     
  10. hagar

    hagar member

    Joined:
    Dec 2, 2004
    Messages:
    374
    Location:
    Columbia, SC
    Just get the Lee powder measure. They only cost $25 or so, and will throw more accurate charges than other brands costing much more.
     
  11. IrvJr

    IrvJr Member

    Joined:
    Jan 6, 2003
    Messages:
    265
  12. koja48

    koja48 member

    Joined:
    Feb 21, 2005
    Messages:
    1,912
    Location:
    SE WA State
  13. hagar

    hagar member

    Joined:
    Dec 2, 2004
    Messages:
    374
    Location:
    Columbia, SC
    That's the one, the Lee Perfect Powder Measure. I use 231, 296, 540 and Accurate #9 for my handgun loads, and 4350, Varget, RL15, RL22 for my rifle, and it performs very well with everything I tried. It will consistently throw within 1/10th of a grain even with extruded powders.
     
  14. ranger335v

    ranger335v Member

    Joined:
    Dec 3, 2006
    Messages:
    3,797
    I like the Redding measures with both chambers, large and small, to cover both rifle and pistol.
     
  15. dcloco

    dcloco Member

    Joined:
    Jan 31, 2006
    Messages:
    319
    Most of the powder measures are the same. But the biggest difference - micrometer adjustment. The Redding & Hornady upper end measures come with these. RCBS - have to purchase seperately.

    I use my Uniflow with large micrometer to measure HS6 loads for my 357 & 44 mags....to IMR3031 for middle bore rifles. Works excellent.

    Some powders will always require you to trickle in the last few grains (IMR3031!!!). Ball powders....by the 7th or 8th round....you are done...just keep pulling the handle. I DO check a random sampling of every 50 rounds.

    I visually check EVERY pistol round - no double charges for me please!!!!

    I also visually check every rifle round.

    ....after all...it is only your weapon, hands, eyes, and life.
     
Thread Status:
Not open for further replies.

Share This Page