Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

removing stuck sabot/bullet?

Discussion in 'Blackpowder' started by rajb123, Mar 4, 2012.

  1. rajb123

    rajb123 member

    Joined:
    Dec 22, 2010
    Messages:
    892
    I have owned this gun for 20 years and have always been able to shoot any "stuck" charge out of the gun - a thompson cap gun.

    I may have to pull the bullet out from the muzzle; is there a special tool for this?
     
  2. loose noose

    loose noose Senior Member

    Joined:
    Feb 22, 2012
    Messages:
    2,555
    Location:
    Southern Nevada
    A screw that fits in the threaded end of a ram rod, it looks similar to a wood screw, All you do is put even pressure on the ram rod with the screw in place and turn it clock wise once the screw gets a bite on the lead pull the ramrod out as evenly as you can. Should get the hunk of lead out. ;)
     
  3. ThorinNNY

    ThorinNNY Member

    Joined:
    Jan 26, 2012
    Messages:
    532
    Location:
    3 hours North of Syracuse, 2 hours west of Lake Ch
    Yes. it`s called a bullet puller. one end screws into your range rod or ram rod. The other end has a pointed wood screw thread to dig into the bullet. In the middle of the tool is a brass ring to prevent scoring the bore. CVA makes `em, others do also.
     
  4. TheRodDoc

    TheRodDoc Member

    Joined:
    Feb 4, 2010
    Messages:
    377
    Location:
    Iowa
    I don't think the screw puller will work for a pointed sabot bullet.
     
  5. rajb123

    rajb123 member

    Joined:
    Dec 22, 2010
    Messages:
    892
    Ok - thanks

    The bullet inside the sabot is a hollow point, so I think I should be able to yank it out with a screw tool.

    Apparently the chamber is contaminated with an anti-rust liquid spray so the powder charge won't fire - UHG.
     
  6. arcticap

    arcticap Senior Member

    Joined:
    Mar 20, 2005
    Messages:
    6,185
    Location:
    Central Connecticut
    Shooting it out should only require trickling in a few grains of powder under the nipple. And a cotton swab can be used to dry out that small area under the nipple before trickling in the powder. If the muzzle is kept pointed downward then the liquid shouldn't contact the fresh powder, especially if it's being fired off right away afterward.
    That saboted bullet may be really tight in the bore making it difficult to pull.
    There's also the new RMC CO2 discharger kit that comes with adaptors and has a multitude of uses:

    EC-Unloader CO2 Discharger

    http://www.rmcsports.com/rmcsports_cfmfiles/newproduct.cfm
     
    Last edited: Mar 5, 2012
  7. robhof

    robhof Member

    Joined:
    Oct 18, 2009
    Messages:
    938
    Location:
    Bowling Green Ky.
    If you have a compressor and some sturdy hose (I cut an old grease gun hose)you can blow it out with that. The hose will fit snugly over the nipple and you can attach the other end to a blow nozzle with a small pipe clamp.
     
  8. PapaG

    PapaG Senior Member

    Joined:
    Sep 12, 2010
    Messages:
    1,869
    Location:
    Il
    take a #8 wood screw, cut off the head and thread the shank 8-32. It will screw into your range rod just like the jags do. the thread should bite well into the lead inside the h.p. Pull.
    If you do decide to shoot it out....after trickling in powder, be sure to reseat the slug or it will act just like an obstruction if it has moved away from the breech.
     
  9. rajb123

    rajb123 member

    Joined:
    Dec 22, 2010
    Messages:
    892
    I live in a residential area, so I can't attempt to shoot out the load until I get to the rifle range.... perhaps next Saturday....

    Will the pirodex that is in the bore now degrade in the next few days? Is it better to load black powder or pirodex under the nipple?

    Thx...
     
  10. ThorinNNY

    ThorinNNY Member

    Joined:
    Jan 26, 2012
    Messages:
    532
    Location:
    3 hours North of Syracuse, 2 hours west of Lake Ch
    Use black powder, 3 f if you have or can get it - to dribble in through the opening when the nipple is out. You don`t need a lot, all you want is to get the bullet completely out of the barrel.
    I remember Flintlock shooters having to use Black Powder in their pans to set off Pyrodex main loads.
     
  11. Zeke/PA

    Zeke/PA Senior Member

    Joined:
    Feb 24, 2005
    Messages:
    2,286
    Location:
    Southeastern Pa.
    I have a tee-handled range rod that I made years ago with a threaded end that accepts a "puller" made from a #10 wood screw.
    For this kind of stuck bullet chore, a wooden ramrod is next to worthless especially if the brass ramrod ends are not cross pinned.
    The tee handle of course makes the job much easier.
    I dont really care for the "shooting it out" idea.
     
    Last edited: Mar 5, 2012
  12. rajb123

    rajb123 member

    Joined:
    Dec 22, 2010
    Messages:
    892
    I do have a 150LBS air compressor; how would you seal the air against the nipple fitting at the breach of the gun?

    I would think this would take a lot of presuure to move the charge/bullet to the muzzle.
     
  13. Superdave70_02

    Superdave70_02 New Member

    Joined:
    Jul 26, 2011
    Messages:
    28
    I pulled a stubborn ball once by braising a 2" dry wall screw to an aluminum rod I found at the farm. Bent a 90 degree handle on the other end. Tape the weld with Teflon tape to protect barrel and help center rod. The drywall screw was very easy to screw into the lead ball.
     
  14. Zeke/PA

    Zeke/PA Senior Member

    Joined:
    Feb 24, 2005
    Messages:
    2,286
    Location:
    Southeastern Pa.
    You BRAZED a screw to an ALUMINUM rod ??
     
  15. Superdave70_02

    Superdave70_02 New Member

    Joined:
    Jul 26, 2011
    Messages:
    28
    It was some sort of special purpose rod that my dad had bought at a farm and ranch show. It was kind of like an aluminum rod but kind of like a nickel rod for cast iron. He buys weird stuff to play around with when he's bored.
     
  16. MCgunner

    MCgunner Senior Member

    Joined:
    Dec 3, 2005
    Messages:
    24,903
    Location:
    The end of the road between Sodom and Gomorrah Tex
    No fuss method that has worked for me several times. I don't need no stinkin' CO2 cartridges to do this, either. I do have a puller and have used it in the past to unload after a hunt when I didn't wanna shoot, but the powder stays so has to be shot out anyway. I don't use that puller, but have it here just in case.

    Inlines are special. :D
     
  17. Zeke/PA

    Zeke/PA Senior Member

    Joined:
    Feb 24, 2005
    Messages:
    2,286
    Location:
    Southeastern Pa.
    Special Purpose rod of some kind?
    It was NOT Aluminum.!!
    If it was, you have created a new world of joining dis-similiar metals.
    Congratulations as your talents will make you a Multi-Billionaire in short order.
     
  18. alsask

    alsask Member

    Joined:
    Apr 23, 2011
    Messages:
    150
    Get a grease zirc that is the same thread as your nipple. Screw it in and pump it out with a gease gun.
     
  19. rajb123

    rajb123 member

    Joined:
    Dec 22, 2010
    Messages:
    892
    I shot this out with some BP under the nipple,,,,,
     

Share This Page