Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Ruger 22/45 question

Discussion in 'Handguns: Autoloaders' started by Rittmeister, Jun 14, 2013.

Thread Status:
Not open for further replies.
  1. Rittmeister

    Rittmeister Member

    Joined:
    Dec 31, 2002
    Messages:
    371
    Location:
    Cincinnati OH
    So - I recently picked up a MkIII 22/45 and had it to the range today for the first time. I was QUITE pleased with the accuracy, as I was shooting 1/2-dollar sized groups offhand at 10 yards. I know that's no great shakes but it's good for me ;)

    Anyway, I had done a good bit of research on the pistol before purchasing and had read a number of times that you should not use the bolt catch to release the bolt (which is natural to me from my experience with other semiautos). This annoyed me but I was prepared to slingshot the bolt when reloading, just to follow directions and ensure long life for the pistol's parts.

    However, I found today that I could NOT chamber a new round by slingshotting the bolt when it was locked back. I would pull on it, but it wouldn't move forward when I released it. When I pushed down on the bolt catch, the gun would chamber a new round no problem.

    On closer examination I found that the bolt catch seems to have a spring-loaded ball detent similar to the thumb safety on a Hi-Power. This detent appears to hold the bolt catch in its upward position even when I pull back on the bolt to chamber a new round.

    If I load a new magazine with the bolt forward and the bolt catch down, I can chamber a round by pulling the bolt back and releasing, as it should.

    Anyone else have this issue?
     
  2. wally

    wally Member

    Joined:
    Jan 2, 2004
    Messages:
    12,353
    Location:
    Houston, Tx
    Its a quirk of the 22/45 MKIII sling-shotting the bolt doesn't work after inserting a fresh magazine, annoying, but it is what it is :(

    Drives my wife batty as she hates the levers since they can be hard on her manicure :)
     
  3. The_Guy

    The_Guy Member

    Joined:
    Dec 13, 2012
    Messages:
    18
    check out the slingshot mod for the 22/45
     
  4. Fishbed77

    Fishbed77 Member

    Joined:
    Nov 23, 2010
    Messages:
    3,036
    Strange. I can slingshot my Mark III just fine.
     
  5. mjsdwash

    mjsdwash Member

    Joined:
    Jan 14, 2011
    Messages:
    559
    yea, my mk lll standard has no issue. Maybe the plastic frame.
     
  6. weblance

    weblance Member

    Joined:
    Sep 15, 2011
    Messages:
    859
    The Mark III 22/45 requires the bolt stop lever to be manually pushed downward, while pulling back the bolt. Do the "slingshot mod" and gravity will drop the lever for you. There are also mods that use a spring to push down the lever.
     
  7. Dentite

    Dentite Member

    Joined:
    Sep 6, 2009
    Messages:
    758
    I just hold the button down with my thumb while I sling-shot it.
     
  8. Rittmeister

    Rittmeister Member

    Joined:
    Dec 31, 2002
    Messages:
    371
    Location:
    Cincinnati OH
    Ah so! This is normal. Interesting. Hilarious that all over various 'boards I'm told to slingshot and not use the catch, but you gotta hold down the catch to slingshot it.

    I'll look up the slingshot mod. I've already got a bushing on order to remove the mag disconnect, so I'll have it apart soon for that; might as well do both at once.

    Thanks all!
     
  9. weblance

    weblance Member

    Joined:
    Sep 15, 2011
    Messages:
    859
    I have a Mark II Target I bought new in the 80s. I was shocked when I bought my first Mark III 22/45. I have always slingshotted the Mark II and thought my 22/45 had been shipped without the spring loaded release lever. Only after I bought 2 more 22/45s did I realize they were designed that way. I prefer the 22/45, but pushing down the release lever always seemed odd to me. Every other auto pistol I own has a spring loaded release lever.
     
  10. wally

    wally Member

    Joined:
    Jan 2, 2004
    Messages:
    12,353
    Location:
    Houston, Tx
    The MK III is a quite different pistol than the 22/45 MKIII, although the uppers are pretty close to being the same.
     
  11. Pilot

    Pilot Member

    Joined:
    Dec 29, 2002
    Messages:
    6,634
    Location:
    USA
    I have four MK II's, but if I was forced to buy a MK III I would certainly remove the mag disconnect, and loaded chamber indicator, and if it was a 22/45 I'd also do the sling shot mod.
     
  12. StrutStopper

    StrutStopper Member

    Joined:
    Jul 5, 2011
    Messages:
    633
    Yeah, from the factory you need to hold the bolt catch down while slingshotting. If you pull out the detent and spring (gravity slingshot mod) then you won't need to worry about holding the catch down. It will slingshot without holding the catch. There are some other spring-assisted mods available to make sure the bolt catch stays down but the gravity mod has worked fine for me. Best thing, its free. You're removing parts, not adding anything.
     
  13. CZ9shooter

    CZ9shooter Member

    Joined:
    Jul 29, 2012
    Messages:
    900
    I did the mod first without adding the spring. Then later added the spring. YouTube taught me how to do it. Now it works just like every othe semi auto I own.

    Took apart a couple ball point pens til I found a spring of appropriate diameter. Then cut to length.
     
    Last edited: Jun 17, 2013
  14. Rittmeister

    Rittmeister Member

    Joined:
    Dec 31, 2002
    Messages:
    371
    Location:
    Cincinnati OH
    Just installed the new bushing to remove the mag disconnect. Mags drop free, trigger pull is a little nicer. Will have to decide about the slingshot mod - getting it back together was a little fiddly until I realized that the sear had rotated out of place while I wasn't looking. It's good to go now but for a little bit there I was confused...

    Anyway, thanks for all the input!
     
  15. hentown

    hentown Member

    Joined:
    May 13, 2012
    Messages:
    1,742
    There's nothing to the slingshot mod. You just remove the detent and spring from the bolt release. Just push out the trigger pin and pull the trigger up so you can get the bolt release out. Really simple. Even Gump could do it! (probably blindfolded)
     
  16. 1KPerDay

    1KPerDay Member

    Joined:
    Jan 19, 2006
    Messages:
    12,703
    Location:
    Happy Valley, UT
    google bullseye gun aw hell... here you go
    http://www.guntalk-online.com/2245detailstripping.htm

    :)

    best detailed how-to I've ever seen.

    As noted above, simply remove the spring and plunger from the slide stop... it'll work by gravity just like the MK1 and MKII pistols do.

    Easy, peasy.
     
  17. CowardlyHero

    CowardlyHero Member

    Joined:
    Nov 9, 2010
    Messages:
    27
    Personally I dont like the sling-shot mod on my gun as the slide release rattles around with nothing to hold it in place after you remove the spring and plunger. YMMV
     
Thread Status:
Not open for further replies.

Share This Page