Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Ruger 22LR (Mark 1?) Failure to Feed - What went wrong?

Discussion in 'Handguns: Autoloaders' started by DefiantDad, Jul 18, 2012.

Thread Status:
Not open for further replies.
  1. DefiantDad

    DefiantDad Member

    Joined:
    Jun 1, 2012
    Messages:
    499
    At the range practicing today, the Ruger 22LR I rented (older model, probably older than Mark III) had one Failure to Feed. I racked the slide, it refused to go forward.

    I took out the magazine and the bullet of the top round had a dent in it, across. I checked that it was seated properly and put the magazine back in, and racked the slide again, and again the slide refused to close.

    So I basically just took out that top round and then everything was fine afterwards.

    So my question is, as a newbie, what happened to that round and why is there a dent? (A line across the bullet).
     
  2. greyling22

    greyling22 Member

    Joined:
    Aug 6, 2007
    Messages:
    4,341
    Location:
    East Texas
    I had a ruger pistol (pre mark 1) that had some slightly bent feed lips on the magazine when I bought it. it caused some misfeeding. I fixed it with a leatherman.

    My first guess is that the feed lips allowed the cartridge nose to rise up too high and it missed the chamber and got pinched by the closing bolt. But that is just a guess. Was is a hollow point?
     
  3. DefiantDad

    DefiantDad Member

    Joined:
    Jun 1, 2012
    Messages:
    499
    Hmmm. Good question. I didn't really think about that because I just rented it and bought a box of 100. I believe it WAS hollow point. I recall seeing a little hole at the front. Made by CCI.
     
  4. The M

    The M Member

    Joined:
    Nov 8, 2011
    Messages:
    82
    Location:
    Orlando
    I've had this happen with my old Mark 1 and my Walther PP. It appears to be weak mag springs which don't hold up the nose of the cartridge at the proper angle. The nosediving bullet is then forced into the bottom of the feed ramp, denting the bullet.
     
  5. DefiantDad

    DefiantDad Member

    Joined:
    Jun 1, 2012
    Messages:
    499
    Is this likely to happen to larger calibers or mostly just the 22LR with everything being smaller and lower spring pressures, etc?
     
  6. ShadowsEye

    ShadowsEye Member

    Joined:
    May 15, 2012
    Messages:
    68
    No pistol or ammunition is 100% guaranteed reliable, no not even revolvers. That being said .22 LR is the most picky and least reliable of the bunch and it's generally not considered to be a self defense round.

    The 22 you happened to rent was last made in 1981, not sure how many thousands of rounds the pistol or the magazine had, but 1 failure (of any kind) out of 100 rounds is not that bad.

    That being said, I have 9mm pistols that have had zero malfunctions in over 1000 rounds.
     
  7. Drail

    Drail Member

    Joined:
    Jan 17, 2008
    Messages:
    5,378
    Most rental guns are maintained extremely poorly. .22 pistols get LOTS of carbon crud packed into them. Rimfire ammo is awfully dirty. You are lucky if you get one that is 90% reliable. I have been shooting MK IIs for twenty years (currently own three)and they are very good pistols. But you gotta clean them if you want to shoot them. MK II magazines get really dirty too and you have to clean them. Amazingly they work pretty well even if you don't maintain them.
     
  8. DefiantDad

    DefiantDad Member

    Joined:
    Jun 1, 2012
    Messages:
    499
    Good points all. The range even told me they hardly clean the guns. At least they are honest! Haha.
     
  9. murf

    murf Member

    Joined:
    Nov 16, 2010
    Messages:
    3,075
    Location:
    arizona
    the round probably got bent some how. the 22lr is a heeled bullet with very little bullet inside the case. it is fairly easy to bend the cartridge right where the case and bullet meet.

    a bent cartridge won't feed correctly in any semi-auto.

    murf
     
  10. ku4hx

    ku4hx Member

    Joined:
    Nov 8, 2009
    Messages:
    2,794
  11. Carl N. Brown

    Carl N. Brown Member

    Joined:
    May 10, 2005
    Messages:
    7,930
    Location:
    Kingsport Tennessee
    I should not have to post this, but experience has taught me otherwise:

    If you are not having problems with your magazines, do not make the modifications to yours just because some one else benefited from modifying theirs.

    Most problems I have had with semi-auto firearms were magazine related. Replacing the magazine is relatively cheap. Modifying a bad magazine (worn, bent, etc) to match a good magazine that works is cheaper.

    what works with one design may not work with a different design.

    With some designs (the AR-7 fer instance) spreading the feed lips will cause feed problems; controlled feed in the AR-7 requires that the cartridge be pinched between the forward part of the feed lips and the newer AR-7 magazines have a wire spring added to serve the purpose of maintaining control as the cartridge feeds from the magazine.
     
  12. DefiantDad

    DefiantDad Member

    Joined:
    Jun 1, 2012
    Messages:
    499
    I practiced at the range again today.

    The 22LR had failure to feed again and one stovepipe. But when it was shooting good, it was real easy to get the bullets to go where you want them.

    Shot 50 rounds out of a Sig 226 today for the first time. Pretty good gun.
     
Thread Status:
Not open for further replies.

Share This Page