Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Ruger Clip or Magazine loader

Discussion in 'Handguns: Autoloaders' started by carsonbm, Jul 27, 2007.

Thread Status:
Not open for further replies.
  1. carsonbm

    carsonbm Member

    Joined:
    Apr 3, 2006
    Messages:
    92
    Location:
    Reminderville, Ohio
    Please let me know what is a good loader and where to find it, for a Ruger Mark III and Mark II.
     
  2. kingpin008

    kingpin008 Member

    Joined:
    Jun 6, 2006
    Messages:
    5,435
    Location:
    Howard County, Merry Land
    Well, for beginners - If you have a revolver you'll be loading the cylinder and not a clip or a magazine.

    If you're looking for a speedloader for a revolver, try HKS. They make some pretty decent ones. Or, have a look around for Bianchi Speed Strips. Little bit different, but plenty of folks swear by them.

    Other than that, load those shells by hand! Whatever you choose, practice is what'll make you quick.

    ETA - You can find speedloaders and speed strips on any number of gun-related websites. Try Midwayusa.com, cheaperthandirt.com, Brownells, etc. Plenty to choose from.
     
  3. ugaarguy

    ugaarguy Moderator Staff Member

    Joined:
    Mar 19, 2006
    Messages:
    12,012
  4. YosemiteSam357

    YosemiteSam357 Member

    Joined:
    Mar 4, 2007
    Messages:
    194
    Location:
    Oregon, USA
    Well, for beginners, not all Rugers are revolvers. In fact, the Mark II and III the OP asked about are specifically magazine fed semi-auto .22 pistols. (Oh, I see the confusion - it was posted in Revolvers. Sorry...)

    That said, I've never seen a mag loader for a Ruger .22. That little button on the side of the mag is there so you can lower the follower with one hand while you put rounds in with the other. That's about all a traditional mag loader does for you anyway, just take a little tension of the follower so you can insert the next round.

    As an aside, I've never been a real fan of mag loaders in general, as they don't seem to save much time. Though I have not used an LULA-type loader, which are the latest hot thing, and a "full auto" guy I know swears by them.

    Finally, there are pedants on this board who will point out that these things are called "magazines" or "mags", not clips. I'll just save them the time... ;)

    -- Sam
     
  5. kingpin008

    kingpin008 Member

    Joined:
    Jun 6, 2006
    Messages:
    5,435
    Location:
    Howard County, Merry Land
    Yosemite - I realize not all Ruger's are revolvers. However, seeing as how this was posted in the Revolver forum, I went that route.

    You are correct though. I have a MK III and haven't found a decent loader for it besides my own hands. Perhaps I should have clarified..
     
  6. YosemiteSam357

    YosemiteSam357 Member

    Joined:
    Mar 4, 2007
    Messages:
    194
    Location:
    Oregon, USA
    Yeah, that's why I mentioned the forum in my post, too. Dang! I hate it when a good wiseass comment comes up short... ;)

    -- Sam
     
  7. PotatoJudge

    PotatoJudge Member

    Joined:
    Nov 17, 2005
    Messages:
    1,332
    Location:
    Texas
    For the Ruger Mark I, II, or III, the Ultimate Cliploader is excellent.

    http://zaliznockindustries.com/outdoors.htm

    I also have the HKS speedloader that ugaarguy mentioned and it works well enough, but I don't use it since the Ultimate Cliploader is much easier and faster.
     
  8. David the Gnome

    David the Gnome Member

    Joined:
    Jul 28, 2007
    Messages:
    6
    Location:
    Lexington, KY
Thread Status:
Not open for further replies.

Share This Page