Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Ruger Redhawk/Burris Scope mount position

Discussion in 'Handguns: Revolvers' started by bikemutt, Apr 5, 2012.

Thread Status:
Not open for further replies.
  1. bikemutt
    • Contributing Member

    bikemutt Member

    Joined:
    Dec 24, 2010
    Messages:
    4,060
    Location:
    Renton, WA
    I'm rigging a Ruger Redhawk with a Burris variable magnification scope, using the Weigand full rail and scope rings. This is my first scoped handgun so I'm just guessing at a number of things.

    Right now I have the scope mounted as far back on the gun as it can be, my thinking is that'll allow me to keep the handgun as far away from me as possible given the eye relief distances inherent with handgun scopes.

    Concerning the weight of the scope, on one hand I feel the weapon balances better with the scope all the way back, on the other hand, I imagine the additional weight of the scope pushed all the way to the front could help with muzzle flip under dynamic conditions. Under all circumstances the gun will be rested on a tripod so extra barrel weight won't be born by yours truly.

    Since none of this high tech equipment comes with a user guide, I'm turning to the experts for guidance :)

    Mount it forward, in the middle, or all the way back?
     
  2. tryshoot

    tryshoot Member

    Joined:
    Mar 1, 2012
    Messages:
    352
    Location:
    backwoods southwest va
    I have a redhawk (not super) that I had to put a mount on. It has factory scope mounts, but I could not put Leapold 2-7 pistol scope on it with factory mounts. Bought it from Midwayusa. Scope is more to rear.
     
  3. The Old Redneck

    The Old Redneck Member

    Joined:
    Jul 20, 2009
    Messages:
    25
    With good rings and base you have a lot of freedom to mount a scope the way it fits you. I have scopes on everything from .17 to 458 caliber handguns. Scopes, rings, and mounts have come a long way over the years. Try it the way you have it and check everything after 50 to 100 rounds and see if screws are shooting loose. There are good locktite products that hold screws yet can be removed if you need to. Because of ports I have had to set some scopes back more than I wanted to but they work fine. Scopes and the dot sights make shooting so much better as you get older, and greatly increase the distance you can hit.
     
  4. BADUNAME37

    BADUNAME37 Member

    Joined:
    Aug 10, 2008
    Messages:
    4,434
    I mounted a Leupold EER scope on a 454 Casull and adjusted the scope so one of the three TSOB rings was against the turret on the forward end of the scope, that way there could be absolutely no slippage of the scope foreward during heavy recoil.

    It worked out fine, no problems at all, and extremely accurate.
     
  5. bikemutt
    • Contributing Member

    bikemutt Member

    Joined:
    Dec 24, 2010
    Messages:
    4,060
    Location:
    Renton, WA
    OK, I'll start with here as seen in the picture, unless someone sees a problem in the making.

    The front of the scope is probably 1/16" off the rail, should make fitting a scope cover fun!
     

    Attached Files:

  6. 98Redline

    98Redline Member

    Joined:
    Jan 3, 2011
    Messages:
    380
    Location:
    Pennsylvania
    Adjust the scope position based on where you get the best eye relief and don't worry too much about the balance. An inch or two fore or aft will make very little practical difference in how the gun shoots or how much felt recoil is diminished by the weight of the scope.

    If you had something like a red dot where eye relief was not an issue then moving it around to get the best balance is fine, but with a variable power scope let the eye relief be your guide.

    You may already know this but for the sake of completeness, the higher the magnification the less tolerant the scope will be of eye relief variation (i.e. Set the scope position based on your highest anticipated magnification setting).
     
  7. BADUNAME37

    BADUNAME37 Member

    Joined:
    Aug 10, 2008
    Messages:
    4,434
    I have a 500 Magnum in 4" flavor that I want to add a Leupold EER, 4X or 1-4X. I have finally found Wiegand (sp) mounts that appear to be about as tough as any other where the milled section lays in where the rear sight lies. Between that and three screws into the gun, the mount should be fine.

    I am thinking I might want four rings just because some of my loads are really nasty. Another thing is

    I should leave the compensator on that does not direct any gases upward as I don't want to blast the front lens!
     
  8. skidder

    skidder Member

    Joined:
    Mar 26, 2011
    Messages:
    1,115
    Location:
    Montana
    Bikemutt-- does that mount require drill and tap? I'm looking for something for my redhawk. That setup ya got looks pretty sweet.
     
  9. svtruth

    svtruth Member

    Joined:
    Mar 10, 2005
    Messages:
    1,698
    Location:
    Bradford, VT
    Unless your reacquisition skills are a lot better than mine, muzzle flip is a small part of time to next shot.
     
  10. bikemutt
    • Contributing Member

    bikemutt Member

    Joined:
    Dec 24, 2010
    Messages:
    4,060
    Location:
    Renton, WA
    Last edited: Apr 7, 2012
Thread Status:
Not open for further replies.

Share This Page