Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Ruger Security Six boot grip?

Discussion in 'Handguns: Revolvers' started by plateshooter, Sep 23, 2012.

Thread Status:
Not open for further replies.
  1. plateshooter

    plateshooter Member

    Joined:
    Dec 24, 2002
    Messages:
    461
    Location:
    N.E. Ohio
    I have a 2.75" Security Six and am looking for a "boot" type grip for it. I have the stock grips, and the "Pachmier (sp)" rubber grips, and the Ruger full size target grips. I am looking for something that still gives a good grip but is easier to use for ccw.

    Any suggestions would be appreciated.
     
  2. mavracer

    mavracer Member

    Joined:
    Jan 9, 2007
    Messages:
    4,393
    Location:
    wichita
    Call Badger he doesn't list them on his site but does still make a few. I just got these for my Speed Six.
    [​IMG]
     
  3. Deaf Smith

    Deaf Smith Member

    Joined:
    Feb 7, 2004
    Messages:
    4,512
    Location:
    TEXAS!
    Eagle used to make the 'Secret Service" line for the Speed Six.

    [​IMG]

    Yep they are mine above. I don't think Eagle makes them now but they should!

    Failing that, Badger.

    Deaf
     
  4. plateshooter

    plateshooter Member

    Joined:
    Dec 24, 2002
    Messages:
    461
    Location:
    N.E. Ohio
    Thanks for the suggestions. I will check them out.
     
  5. WoodchuckAssassin

    WoodchuckAssassin Member

    Joined:
    Apr 5, 2012
    Messages:
    654
    Location:
    Lynchburg, VA
    I loooooove those boot grips! I plan on getting a set put on my old 686 no-dash. I was going to go through Badger, also.
     
  6. Deaf Smith

    Deaf Smith Member

    Joined:
    Feb 7, 2004
    Messages:
    4,512
    Location:
    TEXAS!
    [​IMG]

    Secret Service stocks on my 2.5 inch 686 (among others!)

    Deaf
     
  7. Confederate

    Confederate Member

    Joined:
    Feb 19, 2005
    Messages:
    3,138
    Location:
    Bethesda, MD
    It's not too difficult to change the square grips to round butt grips. You can also use a Tyler T-Grip Adapter, which would be my first choice. But I also like the round butt for guns up to 4-inch barrels.

    [​IMG]

    Ruger with a T-grip adapter.



    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    The two bottom pistols have round butt grips that feel great. I wouldn't
    put round grips on a 6-incher, though.
     
  8. mesinge2

    mesinge2 Member

    Joined:
    Feb 12, 2009
    Messages:
    2,219
    Location:
    Central Florida
    Thanks, mavracer!!

    I didn't know those existed. I will so be ordering a set for my 2.75" Speed Six.
     
  9. Deaf Smith

    Deaf Smith Member

    Joined:
    Feb 7, 2004
    Messages:
    4,512
    Location:
    TEXAS!
    Confederate,

    I did that to my 4 inch blued Security Six just this weekend. Bench grinder and used old RB Speed Six grips to scribe against. Then polished and cold blued before putting on pachmayr RB grips like you have pictured.

    Also, of course, I did that a while ago to my 2 3/4 Stainless Six.

    [​IMG]

    But it's just to pretty to shoot!

    Deaf
     
  10. mavracer

    mavracer Member

    Joined:
    Jan 9, 2007
    Messages:
    4,393
    Location:
    wichita
    Yes they look good on Smiths too
    [​IMG]
    for that matter they look good on Colts too
    [​IMG]
     
Thread Status:
Not open for further replies.

Share This Page