Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Ruger super blackhawk trigger question

Discussion in 'Handguns: Revolvers' started by ArkansasFatboy, Feb 29, 2012.

Thread Status:
Not open for further replies.
  1. ArkansasFatboy

    ArkansasFatboy Member

    Joined:
    Aug 23, 2006
    Messages:
    158
    Location:
    Jonesboro Arkansas
    I'm asking this question for a friend who is wanting to lighten the trigger pull on his Super Blackhawk. 44mag. He had heard something about removing the grips and unhooking a spring to lighten the trigger pull. I was some what skeptical of this and told him I would ask you guys about this. Any info appreciated
     
  2. 98Redline

    98Redline Member

    Joined:
    Jan 3, 2011
    Messages:
    384
    Location:
    Pennsylvania
    Yes you can remove one leg of the trigger return spring (just take one side off the post) to lighten the trigger pull a bit however you do run the risk of the hanging leg binding up in the mainspring.

    A better way to do it is to remove the spring completely and use a set of needle nose pliers to bend both legs equally to reduce the trigger pull.

    Take a look here: http://www.cylindersmith.com/triggerspring.html

    By far the best way to do this is to simply replace the trigger spring with a Wolf reduced power trigger return spring. You can buy an entire shooters pack for a Ruger Single Action from Midway for $13.00 (http://tinyurl.com/7knazz2)

    Just my $0.02: Stick with either the factory or heavier mainspring, don't go to a lighter one. Depending on your particular gun a lighter mainspring, while helping to reduce the trigger pull can result in light primer strikes and failure to fire.

    If you want to really do it up right, take it to a smith and for about $80 they can slick up the trigger and reduce the pull to a nice crisp 2.5 to 3.5# weight.
     
  3. Salmoneye

    Salmoneye Member

    Joined:
    Jan 26, 2012
    Messages:
    1,789
    Location:
    The West Coast Of New England
    As stated, unhooking one side of the spring is not the 'correct way', but many, many people do it without incident...

    The thing to watch for is that one side wants to hang, and the other wants to 'hang up'...

    On a Blackhawk I have, the right leg wants to hang, and if I do the left side instead, it will occasionally bind...

    On an SBH I have, it is exactly opposite...

    YMMV
     
  4. MikeJackmin

    MikeJackmin Member

    Joined:
    Feb 24, 2005
    Messages:
    1,526
    FWIW I've unhooked one leg of the spring from both my blackhawks and they have performed perfectly ever since. Until I saw this thread I had no idea it was even an issue.

    Try it, see if it works. If it hangs up, just hook it back.
     
  5. -eaux-

    -eaux- Member

    Joined:
    Nov 4, 2009
    Messages:
    321
    Location:
    Louisiana
    *just my humble experience/your mileage may vary comment*

    Shoot the heck out of it and it'll be slick as glass. Just about any Ruger SA revolver is gonna be a little rough out of the box, but with repeated cycling (dry and live fire) it'll polish itself smooth all by itself.
     
  6. BCRider

    BCRider Member

    Joined:
    Nov 15, 2008
    Messages:
    7,771
    Location:
    Pacific North"Wet" Coast of Canada
    I've unhooked one side as well and it's working fine.

    eaux, there is two things to the trigger pull feel. One is the return spring tension which must be overcome to move the trigger back and the other is the smoothness of that movement.

    You're right that some dry firing will burnish the surfaces and result in a smoother feel. But you'll never lighten the effort required if the stock spring is left alone or not replaced. And for many of us the stock spring results in an undesirably heavy effort being needed to pull the trigger. Especially for bullseye or plinking.
     
  7. 98Redline

    98Redline Member

    Joined:
    Jan 3, 2011
    Messages:
    384
    Location:
    Pennsylvania
    Actually there is one more thing that effects the trigger feel and that is the creep.

    Even a smooth as glass trigger will have an undesirable amount of creep if left the way the factory sends them out. Changing the amount of trigger to hammer engagement is how you adjust that, however without the proper fixtures you shouldn't even consider messing with it. Just a hair off angle or too aggressive with the stone and you will be buying a new hammer or end up with a gun that could drop the hammer unexpectedly.
     
  8. Hunt480

    Hunt480 Member

    Joined:
    Jan 27, 2010
    Messages:
    445
    Location:
    Georgia
    The SBH Ruger is easy to disassemble and reassemble...I am not a gunsmith but am a notorious tinkerer. I love to work on Ruger triggers and have learned a few tricks to clean up the triggers... I take all my Rugers apart and polish the trigger and hammer...I have a "very very mild glass stone" I use first than I use a Dremel tool and the Dremel polish compound. I have found that polishing alone helps SRH's and SBH's and would probably be good enough for most folks. If you don't over do it you can hawn and polish away just about all of the creep from the trigger if you polish the "trigger notch in the hammer only"...You can remove one leg of the trigger spring but just order a lighter wolf replacement spring from Midway instead.. I got 1 SRH and 3 SBH and they all have about a 1.5 to 2 LB triggers with a very slight hint of creepif any. I bought a new SBH Bisely Hunter just 3 weeks ago and have already did the same trigger job to it as well...I hunt with all my handguns and these Rugers now have as crisp of a trigger as you can hope for.
     
  9. Remllez

    Remllez Member

    Joined:
    Mar 9, 2011
    Messages:
    980
    For reliability the $80.00 spent on an action job with new springs is money well spent. Unless shooting for score or hunting a Wolff shooters pack and some trigger time should work well for occasional shooters/plinkers.
     
Thread Status:
Not open for further replies.

Share This Page