Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Seasoning a Parkerized Finish?

Discussion in 'Gunsmithing and Repairs' started by Ironclad, Apr 18, 2011.

Thread Status:
Not open for further replies.
  1. Ironclad

    Ironclad Member

    Joined:
    Apr 27, 2010
    Messages:
    242
    I have been reading online about greasing a parkerized gun and then baking it for a few hours at 250-350 degrees F in order to season it, kind of like a cast iron skillet. Supposedly it protects against rust better.

    Is there any danger of softening or annealing the metal by doing this? I don't know a lot about metallurgy but I have always been told not to heat metal that has been hardened or tempered for a certain application. For example I never sharpen a knife on a fast grinder or heat springs with a torch.
     
  2. Grim Peeper

    Grim Peeper Member

    Joined:
    Feb 10, 2010
    Messages:
    270
    I think comsoline is the only way to do that. Never tried it but would be interested to see some before after pics.
     
  3. dfariswheel

    dfariswheel Member

    Joined:
    Dec 26, 2002
    Messages:
    6,134
    250 to 350 won't harm the actual metal, but better remove all springs.

    If you try this, be very careful about watching the oven since they fluctuate and may have hot spots where the temp is higher.
    Use a good oven thermometer.

    The grease is Cosmoline, which is not like other greases in that it's not a lubricant.
    Cosmoline is no longer made, as I recall something to do with EPA regulations, but you can still find cans of it at gun shows and at some surplus dealers.

    Possibly just as good a treatment is to liberally apply a heavy coat of CLP Breakfree and let it soak for 20 minutes, wipe off and put in use.
    After that, every time you handle it apply a little more. This builds up a protective layer of Teflon "in" the rough parkerized finish.
     
  4. EMC45

    EMC45 Member

    Joined:
    Jul 20, 2008
    Messages:
    622
    RIG gun grease would probably work well too.
     
  5. wow6599

    wow6599 Member

    Joined:
    Apr 6, 2008
    Messages:
    2,417
    Location:
    Wildwood, MO
    I just use Break Free LP (not CLP) under a heat lamp every few days.........don't know when to stop, and don't care. I'll probably be doing this the same time next year - SA Range Officer.
     
  6. Ironclad

    Ironclad Member

    Joined:
    Apr 27, 2010
    Messages:
    242
  7. Jim Watson

    Jim Watson Member

    Joined:
    Dec 24, 2002
    Messages:
    22,855
    Somebody else tried that and got a greasy mess.

    I'd just keep it slathered with whatever lube you have on hand and let the coarse Parkerized surface hold it.

    I wish I knew what Jeff Cooper meant by "oil buffing" a Parkerized rifle.
     
  8. earlthegoat2

    earlthegoat2 Member

    Joined:
    Aug 28, 2008
    Messages:
    4,514
    Location:
    SE GA
    I had a parkerized Hi Power MK II and just oiled it with the Hoppes oil every few days for about a month. Then I started carrying it for the next year. Never did I see a sign of any rust.

    This was after I had a Colt Officers Model that was also parked. I got rid of it because it kept rusting while in my IWB holster because of my sweat/oils. I got rid of it. THis is before I understood what parkerizing actually was and how it worked.
     
  9. Jim Watson

    Jim Watson Member

    Joined:
    Dec 24, 2002
    Messages:
    22,855
    There are a lot of guns finished in cheap black oxide that looks like Parkerizing to the unpracticed eye and gets called that in advertising.
     
  10. One-Time

    One-Time Member

    Joined:
    Aug 18, 2009
    Messages:
    498
    Location:
    Florida
    why? Cats Iron rusts too, all you need is some occasional CLP
     
  11. IlikeSA

    IlikeSA Member

    Joined:
    Mar 19, 2005
    Messages:
    779
    I just get a oil dampened rag and wipe it down about once a week, then lightly wipe some off the grip with a dry rag. It works well for me and the park seems to soak it in. I've used everything from Hoppes to motor oil, and not a single problem.

    I have heard of baking it, but never wanted to incur the wrath of my wife or my folks (before I was married).
     
  12. Ironclad

    Ironclad Member

    Joined:
    Apr 27, 2010
    Messages:
    242
    I guess oiling it real good and shooting it until its hot would have roughly the same effect over time. Maybe that's why the the authors gun looked more like the antiques after baking?
     
  13. 4v50 Gary

    4v50 Gary Moderator Staff Member

    Joined:
    Dec 19, 2002
    Messages:
    18,994
    At Lassen College, after we parkerized the gun, we rinsed and then immersed the gun into a cosmoline dip. The cosmoline dip imparted a green tinge to the gun.
     
  14. earlthegoat2

    earlthegoat2 Member

    Joined:
    Aug 28, 2008
    Messages:
    4,514
    Location:
    SE GA
    As was noted earlier, Cosmoline is apparently not as available these days. However could this be why some of the Springfield GI models have a greenish parkerizing?
     
  15. 4v50 Gary

    4v50 Gary Moderator Staff Member

    Joined:
    Dec 19, 2002
    Messages:
    18,994
    The cosmoline we used at Lassen came from a GI can o' grease. Hence the greenish tinge.
     
  16. dfariswheel

    dfariswheel Member

    Joined:
    Dec 26, 2002
    Messages:
    6,134
    An alternative to a grease bake is something salt water duck hunters often do to their shotgun,
    They apply a heavy coat of a wax like Johnson's Paste wax or the even harder Renaissance brand wax and warm the metal with a hair dryer.
    The wax melts into the rough finish and waterproofs it.

    The reason Cosmoline was supposedly used (NOT Vaseline) is because the Cosmoline would bake into a dry varnish-like coating and wouldn't rub off.
    Vaseline and most lubricating greases won't.
     
  17. JNewell

    JNewell Member

    Joined:
    Oct 1, 2003
    Messages:
    2,714
    Location:
    Land of the Bean & the Cod
    If Gunny saw you putting your rifle in the oven, you'd be next, and the heat would be turned up a lot higher. :D
     
  18. publiuss

    publiuss Member

    Joined:
    Sep 18, 2005
    Messages:
    361
    I always wipe my guns down with an oily rag after using but every once in a while I will give a parkerized gun an "oil saturation". After a complete cleaning I will very liberally(I mean dripping) spray down the gun with Rem oil and leave it overnight. The next day I will simply hose it down again with the oil. I may do this 2-4 times. This lets the parkerizing soak up every bit of oil that it is capable of and really allows the finish to do it's job as a rust preventer.
     
  19. bigfatdave

    bigfatdave Member

    Joined:
    Jul 13, 2008
    Messages:
    5,961
    Location:
    Near Camp Perry
    SA is trying to simulate the look of a GI gun that spent years (decades) in Cosmoline.

    I haven't done the bake yet, I schmear on the grease and let the gun sit for a while whenever I detail strip it. When another .45acp brass unloader arrives I've been planning on trying the bake, Xavier (who posts here, but rarely lately) used vaseline because it wouldn't stain stuff if it bled back out, and I think he has the right idea, I'll likely use either that or another colorless grease (depends what I can find expired when it comes up) from an industrial source.

    If you want a constant low baking temp, a toaster oven with a bunch of mass in it will maintain well, I'd wrap the greased gun parts in a tinfoil pouch, and stick it in the toaster oven with a bunch of old cast iron pans for thermal mass ... a few hours at ~225F or whatever low temp I can maintain should do it.
     
  20. Jim Watson

    Jim Watson Member

    Joined:
    Dec 24, 2002
    Messages:
    22,855
    The Parkerizing process calls for a chromate dip; that has a yellow-green color and might be the source of the tint instead of old Cosmic.
     
  21. Sunray

    Sunray Member

    Joined:
    May 17, 2003
    Messages:
    11,377
    Location:
    London, Ont.
    "...cosmoline dip imparted a green tinge..." Long term storage in cosmoline is what creates the green tinge. Not heat.
    "...a GI can o' grease..." That won't either.
    Repeated oiling of a parkerized finish is what gives it better rust protection properties.
     
  22. btg3

    btg3 Member

    Joined:
    Oct 30, 2007
    Messages:
    1,921
    Apart from turning cosmoline waxy, I suspect the only thing heat does is lower the viscosity of a chosen lubricant for better penetration and wet-out. Some lubricants penetrate and wet-out quite well without heating.
     
  23. brickeyee

    brickeyee Member

    Joined:
    Feb 25, 2005
    Messages:
    3,135
  24. Ramone

    Ramone Member

    Joined:
    Sep 26, 2008
    Messages:
    748
    Location:
    Tidewater VA
    A heavy coat of CLP - like, till it drips, then lay it out in full sunlight for a whole day.

    Wipe it dry, a few days in a row, as the CLP will keep oozing out of the pores.

    If I am not mistaken, this is what Col. Cooper meant by 'oil buffing'. It was also what we were told to do with our brandy new M16A2s when they were first issued to us.
     
Thread Status:
Not open for further replies.

Share This Page