Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

sharpening with two quarters??

Discussion in 'Non-Firearm Weapons' started by JPG1911, Oct 21, 2010.

Thread Status:
Not open for further replies.
  1. JPG1911

    JPG1911 Member

    Joined:
    Oct 15, 2010
    Messages:
    22
    Location:
    Kernersville, NC
    Anybody ever heard of or familiar with this technique? I've seen the ads claiming that all you need to put a razor sharp edge on your favorite cutting tool is two quarters. I am naturally skeptical and i use what works for me, ceramic rods and whetstones, but I always like to see viable new techniques if they are in fact viable. Any info on this would be greatly appreciated. I've googled it many times but to no avail...:banghead:
     
  2. zxcvbob

    zxcvbob Member

    Joined:
    Sep 15, 2007
    Messages:
    5,061
    Location:
    S.E. Minnesota
    Unpossible. However, a quarter or nickel might make a good shim to hold a knife edge at a constant angle to the stone.
     
  3. heron

    heron Member

    Joined:
    Apr 26, 2007
    Messages:
    1,062
    Location:
    NE Ohio
    Sounds bogus to me . . . I'm pretty sure the steel in your blade is harder than the alloy in your pocket change.
     
  4. M-Cameron

    M-Cameron member

    Joined:
    Oct 6, 2009
    Messages:
    2,865
    im assuming it works something like the scissor technique...well in theory it should work....but it sounds terrible for the blade..

    i suppose if you had a beater blade and needed it sharp on a hurry.....i suppose ot would come in handy...
     
  5. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    It would have to be a pretty dang soft knife for a quarter to do anything to the blade.

    You can cut a coin in two by tapping the blade through it with a few whacks on the spine! With no damage to the blade or edge.

    rc
     
  6. hso

    hso Moderator Staff Member

    Joined:
    Jan 3, 2003
    Messages:
    48,718
    Location:
    0 hrs east of TN
    Never heard of anything like it and can't think how the soft material of the quarter would be able to remove steel from the edge.
     
  7. MattTheHat

    MattTheHat Member

    Joined:
    May 22, 2007
    Messages:
    1,044
    Location:
    Plano, TX
    Sounds like a good way to drop a digit.


    -Matt
     
  8. Joe Demko

    Joe Demko Member

    Joined:
    Dec 30, 2002
    Messages:
    6,523
    Location:
    Just two minutes from sanity.
    I've heard of this; but I don't see how you could sharpen a knife with only a couple coins.
     
  9. M-Cameron

    M-Cameron member

    Joined:
    Oct 6, 2009
    Messages:
    2,865
    ok....so i figured id give this a try......

    i had an old folder that was as blunt as a board.....

    i held the two quarters so they were offset....and pulled the knife blade through the gap between them.......


    ...after 60 -70 passes.......my knife is still as dull as when i started.......


    ah well.....guess you cant believe everything to see on the internet......
     
  10. David E

    David E Member

    Joined:
    Aug 3, 2008
    Messages:
    7,455
  11. David E

    David E Member

    Joined:
    Aug 3, 2008
    Messages:
    7,455
    Just goes to show what happens when someone hears about something and then speculates on what they must mean, then posting about the impossibility of it........instead of actually finding out the facts.
     
  12. bikerdoc

    bikerdoc Moderator Staff Member

    Joined:
    Jan 8, 2008
    Messages:
    17,287
    Location:
    Southern Virginia
    IIRC Roy Huntington, the editor of Handgunner mag, wrote an article on sharpening and stated he used 2 quarters to get his initial angle on the stone, then put the quarters away and shapened by hand.
     
  13. Sky

    Sky Member

    Joined:
    Aug 4, 2010
    Messages:
    2,927
    Location:
    Texas
    One of the cheapest knife sharpeners I have ever owned looked like a case that had six washers per-side off set so the washers ended up like your fingers when you bring your hands together with digits enter weaved.

    Think the washers were of pretty low grade iron or steel? The way the washers overlapped they naturally formed a "V" so you just pulled the blade through a couple of times and my my my it sharpened the blade really well.

    The secret was to apply even Pressure.

    No it was not as good as a 20 minute wet stone job but it was extremely fast and worked well.

    You can sharpen a blade all kinds of ways. The above mention sharpener I have not seen for a long time. I think it cost maybe a couple of dollars and has been replaced by something costing $20 or more and that works about half as good.
     
  14. sm

    sm member

    Joined:
    Dec 22, 2002
    Messages:
    28,389
    Location:
    Between black coffee, and shiftn' gears
    As a guide to assist in keeping a constant angle - yes.
    Sharpening - no.

    This is like the old saw about using a coin to determine the choke of a shotgun barrel.
    All this tells you is, you have a coin, and a shotgun barrel.

    But...but two quarters rubbed together, does make a great squirrel call. *yep*
    I was raised to drill a hole in coins, then use a piece of rawhide boot lace to hold them together. (like keys on a beaded key chain, which works fine too).
    Off hand, with lace/chain around little finger, rub coins. When the squirrel turns, providing a shot, let the coins dangle off little finger while you shoot.

    Ain't teh Intraw3bz wunnerful at times? *smile*
     
  15. zignal_zero

    zignal_zero Member

    Joined:
    Dec 5, 2008
    Messages:
    578
    Location:
    West Central Florida
    mabye this idea (2 quarters to sharpen a blade) actually predates the internet and really WAS the price of sharpening when it originally started being re-told :D
     
Thread Status:
Not open for further replies.

Share This Page