Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Side folding stock for AK clone

Discussion in 'Rifle Country' started by bosshoff, Oct 7, 2004.

Thread Status:
Not open for further replies.
  1. bosshoff

    bosshoff Member

    Joined:
    Feb 24, 2004
    Messages:
    246
    Location:
    Chicagoland
    I am sure this has been talked of in the past, but I can't seem to find what I am looking for. I have a Krebs Custom KTR-03S AK variant built on a Saiga action. It is a post ban weapon, and has the mix of US parts etc. I am interested in getting a ide folding metal stock like you would find on a Russian AK. The only two websites I know which sell them are out of stock. These being Tantal and K-VAR. Does anyone know of another source for these stocks? Also, what about the legality of this swap. If I add this folding stock, how many US parts do I need to add to offset the stock? I am sure they count every nut bolt and screw. Thanks in advance.
     
  2. zougou

    zougou Member

    Joined:
    Apr 30, 2003
    Messages:
    136
    Location:
    OR
    The problem is that you usually need a new rear trunion to accomodate the folding stock. You could get the TAPCO stock or the ACE stock and avoid having to change the rear trunion. The Romanian folding stock works with the Romanian trunion in SARs, but I'm not sure if it would work with your Russian trunion. If your current stock is American-made and you put a non-USA made stock on it, you could be in violation.
     
  3. MAKOwner

    MAKOwner Member

    Joined:
    Dec 28, 2002
    Messages:
    682
    About your only option if you don't like the Tapco or Romanian sidefolders is the one from Robinson Arms that fits standard stamped AKs, but unfortunately I understand it's near $200... http://www.ak47.com/VEPR Folding Stock.htm Pic of the non VEPR one down near the bottom

    But by the time you figure in the cost of the Russian/Bulgarian side folding stocks, plus the labor to install the new trunion and such you're probably looking at a comparable price, unless you're going to do the trunion swap and any refinishing work yourself...

    I don't believe the buttstock is US made on the KTRs, so it shouldn't effect the parts count one way or the other. Might want to double check though, if it is you'll need to add one more US part somewhere else to offset the change...
     
  4. Langenator

    Langenator Member

    Joined:
    Jul 30, 2003
    Messages:
    2,689
    Location:
    Ft Belvoir, VA
    I'm far from an expert, but would ACE gunstocks' skeleton stock work?
     
  5. Badger Arms

    Badger Arms Member

    Joined:
    Jan 1, 2003
    Messages:
    3,738
    Location:
    Harnett County, NC
    Try this one:

    [​IMG]

    It screws right on to a wood-stock trunion... no modification. Has a rubber bumper to keep it from marring the right side of the receiver. Cool.
     

    Attached Files:

  6. Dave Markowitz

    Dave Markowitz Member

    Joined:
    Dec 24, 2002
    Messages:
    6,926
    Location:
    Plymouth Meeting, PA
    Badger Arms,

    That AK is EVIL looking! (Which of course is a Good Thing!)

    If you shoulder that rifle from the left shoulder, does your nose bump the stock's hinge? I experience this with my Tapco folder. It isn't painful but it's annoying.
     
  7. Badger Arms

    Badger Arms Member

    Joined:
    Jan 1, 2003
    Messages:
    3,738
    Location:
    Harnett County, NC
    Dave. Nah, notice that the stock is on the centerline when it's extended. You kinda rest your cheek against where it starts to loop down...
     
  8. WhoKnowsWho

    WhoKnowsWho Member

    Joined:
    Dec 25, 2002
    Messages:
    3,432
    Location:
    Maricopa, AZ
    Where is it available from?
     
  9. glocksman

    glocksman Member

    Joined:
    Apr 6, 2003
    Messages:
    537
    Location:
    Evansville, IN
    Federal Arms

    I have the same stock on my WASR-10 and it feels fine when shooting.
     
  10. c_yeager

    c_yeager Member

    Joined:
    Mar 14, 2003
    Messages:
    5,479
    Location:
    Seattle
    Wow the KTR03S is a sweet looking rifle. MUCH better than the one built on the VEPR since you actually HAVE some furniture options. You should be able to fit virtually any of the current side folder to that rifle (just make sure they will fit a standard stamped reciever). Pretty much the only stocks that require a new trunion are the underfolders.

    And yes, ACE does make a reciever block to fit the Saiga rifles so that is an option (which i think would look pretty damn cool).
     
Thread Status:
Not open for further replies.

Share This Page