1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Sights/optics for Mini-14

Discussion in 'Rifle Country' started by Floppy_D, Nov 26, 2008.

Thread Status:
Not open for further replies.
  1. Floppy_D

    Floppy_D Member In Memoriam

    Jul 4, 2007
    NAS Pensacola
    I have a really nice pre-ranch model of the Mini-14, which I like quite a bit. What I dislike, are the sights. I'm a fan of iron sights, but I don't like/can't get the ring and post sights to work for me.

    Here's the question:
    From those of you who have been down this road, which way did you go? Scope mount and dot sight? Reflex sight? Upgraded iron sights? Small magnification scope?

    I have the mount, should optics be needed. I won't be shooting beyond 100 yds. It is a plinker. I don't want to spend a fortune, but I'm not looking for a $30 fix either.

    Which way did you go? Lessons learned?
  2. owlhoot

    owlhoot Member

    Jun 10, 2005
    My friend I feel your pain. Your Mini is probably a 181 series, you can check the first three digits of your serial number to see. I'll tell you what you are up against.

    This little rifle has a very violent action. Violent enough to shake most scopes to pieces in short order.

    To solve this problem you can install a heavy recoil spring, available from Wolfe, Brownells, etc. You can also install recoil buffer pads but the ones I tried didn't fit well at all. much too thick. Then you will need to install a smaller gas port bushing (cheap). Which makes less gas available to work the action. Or you can go first class and install an adjustable gas port (not so cheap).

    Second problem, there aren't any good bridge (receiver) scope mounts available for this rifle. The best is probably B-Square and it is iffy.

    Third problem, the ejected brass is liable to hit your scope. Some rifles have this problem, some don't.

    You can get an after market hand guard with rails that will let you mount a scope forward of the receiver, scout rifle style. These are a little pricy.

    The factory sights on the 181 Mini are indeed an abomination. In my case, I just had a terrible time even seeing through the peep. I fixed this problem by reducing and reshaping the comb of the stock. This really wasn't a big job. Took a pleasant evening using sandpaper only and that included refinishing and blending the new comb. This made a tremendous difference. While the factory sights still sucked, I could at least use them. I next installed a ghost ring rear aperture in place of the factory leaf (peep). That's a five minute job. I haven't yet done so, but I intend to do a little work on the front sight, at the very least, I'll add a gold bead.

    A red dot or reflex sight is great if you are shooting at people at fairly short range. But for a plinking rifle, I wouldn't bother. The dots are mostly 5 moa and that's too large for varmits, at least the small four legged variety. A smaller dot is very difficult to see against many backgrounds.

    You will probably find that your rifle, even with a scope sight is good for no more than 4 or 5" groups at 100 yards. You can cut those groups in half by attaching a five inch or so metal rod to the barrel. Tri clamps are available from Cheaper than Dirt for ten bucks each, you'll need two.
    Use any metal rod roughly the same diameter as the barrel. This is a cheap fix that will do wonders. If you want still better groups, bedding the stock will help some.

    Hope this helps.
  3. dagger dog

    dagger dog Member

    Jan 30, 2008
    SO. IN
    Having KMINI Ranch, and poor eysight topped mine off with a scope right out of the box.

    At the range found out that my pride and joy wasn't a bug hole shooter,after the first three or four rounds it wouldn't shoot under 4"@100 even with handloads.

    The factory ring & mount spacing reduces the optic choices, so I coughed up the $ for a picatinny rail so shorter optics could be mounted.

    Red dot, tried that, short fixed power, tried those.

    Guess what? Went back to the factory "ghost ring" and post.

    The accuracy pontential of the factory Minis in my hands are 4-5"@ 100 with any optic, ammo, and the factory iron sights give me the same.

    Brownells has some iron sights for the Minis, I've been tempted to try a different set, but I think I'll opt for staying with the originals.
Thread Status:
Not open for further replies.

Share This Page