1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Source for M1 carbine parts markings??

Discussion in 'Rifle Country' started by Topgun, Mar 8, 2006.

Thread Status:
Not open for further replies.
  1. Topgun

    Topgun member

    Dec 26, 2002
    Anywhere necessary
    I just picked up a nice old carbine. IBM mfg. I've cleaned it and noted the parts markings and would like to know if anyone has a link to proper parts for proper guns. Tried a search on "M1 carbine markings" and got too much to search.

    It's marked as follows:

    No bayonet lug barrel: IBM CORP 10-43
    Receiver: IBM CORP
    Ser #: 3729XXX
    Front sight: N
    Operating rod: N
    Barrel band: O (maybe Q)
    Adj rear sight: JAO
    Bolt: AOB
    Trigger guard assy: IL (letters truncated)
    Hammer: LTQ (or LTQ)
    Safety: "EW"
    Mag release: M
    Recoil lug: WI (or IM) but the W sides are slanted...odd for an M
    I-cut early stock: RMC cartouche crossed cannons
    Upper handguard: RMC

    I didn't pull the trigger itself out. Couldn't see markings if any.

    I seem to remember RMC being a mark for Rock-Ola. Don't know if IBM made wood for the guns or not.

    Very uniform finish and nicely old inside. Bore mirror clean. Insides haven't been oiled for a LOOOONNNGG time.

    Also not sure if the old early I-cut stocked ones had adj sights. The last early I-cut I had had the flip up sight.

    Any info appreciated. Just so many different markings on the parts makes me curious if it came that way.

  2. loadedround

    loadedround Member

    Feb 18, 2006
    Valley Forge, Pa
    M1 Carbine

    Have you done a search for books on Amazon.com for the Carbine?
  3. Firehand

    Firehand Member

    Mar 16, 2004
    Oklahoma City
    Don't know of an online source. There is a book 'M1 Carbine' that can sometimes be found, it has a section dealing with every manufacturer of the carbine and the various marks they used.
  4. AZ Jeff

    AZ Jeff Member

    Jan 21, 2003
    Phoenix, AZ
  5. shield20

    shield20 Member

    May 21, 2005
    New York
    B- IBM
    W - Winchester
    N - National Post Meter
    RMC - Rockola
    I - Inland (WI - Winchester for Inland, AOB - Auto Ord for IBM, etc)
    AO - Auto Ordanance (sub contractor)
    Q - Quality
    SG - Saginaw
    S'G' - Saginaw Grand rapids
    IP - irwin Pederson
    U - Underwood
  6. Scout180

    Scout180 Member

    Mar 12, 2006
    Visit: http://home.att.net/~ra-carbines/history.html for lots of good data. As far as books go, here are a few:


    The U.S. .30 Cal. Gas Operated Service Rifles: A Shop Manual
    The only really detailed gunsmithing and repair manual on these extraordinary rifles ever published. 100's of crystal clear photos and illustrations. 2nd generation, two-in-one, edition - 383 pages with thread stitched binding and plastic laminated soft cover. 383 pages of brand new and updated material - Not a rehash of old military manuals! Price: $44.95

    And Get this paperback-The U.S. .30 Caliber Gas Operated Carbines, A Shop Manual by Jerry Kuhnhausen, Heritage Gun Books. Same as the other shop manuals in his series about rifles and handguns. Very in depth with info about GI and commercial parts etc. Not cheap but about the last word. I think you can get from Brownells, or from some of the larger gun book dealers at large gun shows. I have several of his shop books. The GI manual reprints are OK for field stripping and basic maint. on your own gun, but are not for full gunsmithing of the carbines. Even goes into advanced accurising for match grade or such work. http://www.sydweedon.com/kuhnhausen.asp $29.95

    The M1 Carbine Owner's Guide by Larry Ruth and Scott A. Duff. - History, development, selecting the rifle, disassembly, assembly, inspection, cleaning, zeroing, and much more.
Thread Status:
Not open for further replies.

Share This Page