Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Springfield TRP model

Discussion in 'Handguns: Autoloaders' started by Lone_Gunman, Jul 20, 2007.

Thread Status:
Not open for further replies.
  1. Lone_Gunman

    Lone_Gunman Member

    Joined:
    Dec 24, 2002
    Messages:
    8,056
    Location:
    United Socialist States of Obama
    I have an opportunity to get one of these, and it looks like a nice pistol but I have never been to fond of Springfields in the past. I have owned a couple of their 1911s, a Loaded, and a Mil Spec, and neither were 100 percent reliable.

    How is the TRP in comparison? Is it a better made pistol? How is it different from a loaded model?
     
  2. scubie02

    scubie02 Member

    Joined:
    Aug 18, 2003
    Messages:
    916
    Location:
    ny
    as I recall, the TRP is sort of a tweaked assemblyline model, sort of a pseudo custom shop gun, as opposed to the full custom shop models.

    I've had numerous Springfield's, and they were all flawless, I'm somewhat surprised to hear of your problems before--that's too bad. These were new guns, not used ones that someone else may have tampered with or something? Lots of people try t "fix" a gun or make it better or replace some part and mess it up, then just trade it in for some other poor slob to get it.

    That having been said, I have never been able to pull the trigger on a springer more expensive than the Loaded, since my Loaded will shoot one ragged hole and is totally reliable, and I can't see how I'd do better than that with one of their more expensive models. If you've got the scratch though, I say go for it.
     
  3. abarth

    abarth Member

    Joined:
    Aug 3, 2006
    Messages:
    90
    I don't know about anyone else, but my TRP has been very reliable except with some of my handloads and 8 rounds mag but once I adjust the OAL everything seen fine. No problem with factory ball or HP loads what so ever. Accurate, reliable, very well put together, and no problem with the MIM parts either.
     
  4. sturmgewehr

    sturmgewehr Member

    Joined:
    Nov 6, 2006
    Messages:
    932
    Location:
    Indiana
    I have over 5k rounds through mine without a single malfunction... I am also using Wilson 47D magazines in it.

    There are two types of Springfield 1911's, ones completely built and assembled in Brazil and those that are built here in the U.S. from Brazilian made parts. The higher end Springfields are built here in the US on Brazilian made parts and typically display superior craftsmanship. You can tell the two apart by a quick visual inspection. The US finished guns have more crisp lettering and markings whereas the Brazilian guns have inferior markings (uneven depth, not always straight).

    The TRP is finished here in the US. All the critical parts are hand fitted by the guys in the Custom Gun Shop. They are among the best 1911 pistolsmiths in the world by the way. You can tell the TRP is touched by them because the slide, barrel and extractor will have hand etched serial numbers on them which tells you those parts were fitted by a smith. The fit, finish and general craftsmanship is second to none. I own Ed Browns and love them, but I enjoy shooting my TRP more... goofy, I know... but it's THAT good.

    Here are some pics:

    5-1.jpg
    6.jpg
    8.jpg
    3.jpg
    4.jpg
     
  5. surjimmy

    surjimmy Member

    Joined:
    Mar 21, 2007
    Messages:
    1,187
    Was told by a reliable custom 1911 builder that a TRP is the best 1911 off the shelf.
     
  6. TX1911fan

    TX1911fan Member

    Joined:
    Mar 7, 2006
    Messages:
    2,013
    Mine has been flawless.

    [​IMG]

    [​IMG]

    [​IMG]
     
  7. Gibbles

    Gibbles Member

    Joined:
    Apr 10, 2007
    Messages:
    149
    Location:
    Utah
    I think Springfield makes great guns, I have an Imbel GI model and a US Loaded model and both are excellent firearms, and have been 100% for me.
    And if its not Springfield has a lifetime warranty.

    In that TRP picture above you can see the quality of the fitting on the beaver tail, My loaded is tight everywhere but its missing the smooth curve of that TRP.
     
  8. 10-Ring

    10-Ring Member

    Joined:
    Dec 24, 2002
    Messages:
    12,037
    Location:
    California
    I like the TRP & from the few times I have shot them, good shooters to boot. If I were in the market to add another 1911 to my collection, it would be on the list of candidates.
     
  9. sturmgewehr

    sturmgewehr Member

    Joined:
    Nov 6, 2006
    Messages:
    932
    Location:
    Indiana
    In that pic I posted of the rear end of the TRP you can see the slide to frame fit, also note the fit of the extractor. It's flawless.

    Here's a shot of my Ed Brown Kobra's slide to frame fit.

    1.jpg

    The TRP is as nice or nicer.
     
  10. TX1911fan

    TX1911fan Member

    Joined:
    Mar 7, 2006
    Messages:
    2,013
    Springfield makes great products. Here is a GI that I had customized. Look at the slide to frame, extractor and beavertail on this one, that started out as a $399 pistol.

    [​IMG]
     
  11. sturmgewehr

    sturmgewehr Member

    Joined:
    Nov 6, 2006
    Messages:
    932
    Location:
    Indiana
    TX, that's a beautiful 1911 you have there. I think you should sell it to me. :p
     
  12. TX1911fan

    TX1911fan Member

    Joined:
    Mar 7, 2006
    Messages:
    2,013
    Thanks sturm, it has been a fun project. It's still not quite perfect, as it is having some problems returning to battery. Still a little too tight, but I'm working with the Custom Shop on it. But it shoots like a dream.
     
  13. AndyC

    AndyC Member

    Joined:
    Mar 21, 2006
    Messages:
    2,581
    Location:
    DFW, TX
    Oh, you guys.... damn you all *sob* ;)

    "One day you will be mine...oh, yes..."

    Some seriously nice hardware there.
     
  14. Gibbles

    Gibbles Member

    Joined:
    Apr 10, 2007
    Messages:
    149
    Location:
    Utah
    Well here is my SS loaded, I have done a few things to it, Greider trigger, EGW bushing, VZ grips, checkered the MSH and the mag button, the Molly Teflon finish, and softened all of the corners I thought were to sharp.
    I have had a few people mistake it for a TRP already. :D
    The skateboard tape gives it away though. ;)

    GibblesLoaded.gif

    1911M4.gif
     
Thread Status:
Not open for further replies.

Share This Page