Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

*TEST* "Short Barrel" 135gr+P Gold Dot Water/Denim

Discussion in 'Handguns: General Discussion' started by Joshua M. Smith, Sep 1, 2007.

Thread Status:
Not open for further replies.
  1. Joshua M. Smith

    Joshua M. Smith Member

    Joined:
    Aug 8, 2004
    Messages:
    1,056
    Location:
    Wabash IN
    Revolver: Rossi M68 1-7/8” Barrel
    Ammunition: 38 Spl Gold Dot “Short Barrel” 135 grain +P

    Readers have been asking for a test of this ammunition. I do not order ammo for my own reasons and was unable to get any. A friend saw my dilemma and sent me a sample.

    In celebration, I built a new test platform.

    Dsc00028.jpg
    This new testing platform is designed to better retain the water jugs. It will take a leaden shield in the back to stop any rounds which may pass through five water jugs. The side shields cover all but the first jug, which many times comes undone in an enthusiastic manner. I believe that it’s better to let this one go as the box may suffer damage, and flying wooden debris are likely more dangerous than flying water.

    Dsc00030.jpg
    This is a dual-purpose box. The sides have holes in them to accept dowel rods. The idea is to turn it into a Fackler box should I decide to use Dr. Fackler’s method.

    Dsc00029.jpg
    The box is marked at 1” intervals so I can make more accurate estimates of penetration.

    On to the test…

    Dsc00051.jpg
    This is one gaping Gold Dot. The bullet has only the slightest of curve before it opens up into the hollowpoint.

    Speer claims a velocity of 860fps from a 1-7/8” barrel from this round. I’ve seen figures published on the Internet which give it over 900fps from the same length barrel.

    Additionally, Speer advertises penetration figures of 11” in bare gelatin, 11” in heavily clothed gelatin, and 13” in gelatin covered with four layers of denim.

    Dsc00031.jpg
    The new setup…

    th_Mov00032.jpg
    … and the shot.

    Dsc00035.jpg
    I found the first jug shredded, on the ground.

    Dsc00033.jpg
    The denim went its own way too, with a bullet hole through the middle.

    Dsc00038.jpg
    The bullet impacted at 21” of water and bounced back a few inches (lower left hand corner). The jug which it bounced off of was cut.

    The shoot looked like a 9mm standard pressure round from a service sized pistol, not a round from a 38 Spl snub nose. Additionally, while recoil was a bit brisk, it was not at all uncontrollable and because it was quick, it was actually quite pleasant from my all-steel revolver.

    Dsc000422.jpg
    These are the numbers I came up with inside after shooting.

    Dsc00044.jpg
    Expansion was about .62”.


    Dsc00047.jpg
    As you can see, the petals folded back further than they probably would have in tissue or gelatin. This is common in water testing.

    The 21” of penetration I got in water through denim would give approximately 10.5” to 13.1” in gelatin, which is consistent with the numbers provided by Speer.

    In summary, it looks like we may have a winner. Though I’m not aware of any actual street usage of this round as of yet, it would seem that it does approximate a standard pressure 9mm round from a service sized pistol. It almost duplicates the performance of the standard pressure 115gr Remington hollowpoint (non-GS) I tested a while back.

    I will carry this load in my revolver and keep the FBI load in a speed loader I have on the way, ready to go on my belt. The test numbers look very promising, but I’m a bit leery of relying solely on data collected in testing, whether it be an informal water test or a more scientific calibrated gelatin test.

    Regardless, this is the only round besides the old FBI load I would feel comfortable using from a snubby to dispatch a coyote. If I get the chance, I’ll report the results. Usually though, I have a long gun with me on my hikes and hunts.

    Hope you enjoyed!

    Josh <><
     
  2. Jim March

    Jim March Member

    Joined:
    Dec 24, 2002
    Messages:
    8,732
    Location:
    SF Bay Area
    Yup. About what we figured :).

    Damn fine slug.
     
  3. stormspotter

    stormspotter Member

    Joined:
    Jun 11, 2004
    Messages:
    423
    Location:
    Missouri
    38 SP "Short Barrel"

    I have some in 357 mag for my S & W Model 19 2 1/2". Looks real good in testing on highpowersandhandguns.com.

    Also going to try the 357 DPX load also. Both this and the Short Barrel Gold Dot are mid-range loads for lighter guns.
     
  4. DevilDog0402

    DevilDog0402 Member

    Joined:
    Jul 9, 2007
    Messages:
    446
    Location:
    Northern VA
    That's pretty impressive!!
     
  5. PTK

    PTK Member

    Joined:
    Mar 25, 2007
    Messages:
    3,712
    Location:
    Montana
    There's more hollow than point in that hollow point! Sure performed well, too. I may have to try to get some of that for my SP101.
     
  6. Lonestar49

    Lonestar49 Member

    Joined:
    Feb 17, 2007
    Messages:
    2,654
    Location:
    So. Calif.
    Nothing goes to waste

    ...

    I'm very impressed with your set up, and test results, with pics.

    Right down to the 2 old PC cases as stands..


    Well done,


    LS
     
  7. Pumpkinheaver

    Pumpkinheaver Member

    Joined:
    Jun 20, 2003
    Messages:
    1,255
    Location:
    missouri
    Yes, it's a damn fine load. I've been packing it for the last few years.
     
Thread Status:
Not open for further replies.

Share This Page