Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Tubb's® Final Finish Bore Conditioning Ammo ????

Discussion in 'Rifle Country' started by NY'er, Feb 12, 2008.

Thread Status:
Not open for further replies.
  1. NY'er

    NY'er Member

    Joined:
    Jan 15, 2007
    Messages:
    96
  2. TheLaxPlayer

    TheLaxPlayer Member

    Joined:
    Jul 2, 2007
    Messages:
    179
    Some people swear by it, most people consider it rubbish. Heck, most people consider break-in rubbish.

    Personally I see nothing wrong with using regular ammo to "break-in" the barrel. I'd just clean it a bit more often until it stops copper fouling as much and then you're good to go. I'm no expert, but Gale McMillan recommended this and he was pretty much the ultimate authority on such matters. According to him, the reason that break-in was made a big deal was simply benchrest barrel makers wanting buyers to wear out their new barrels faster so they'd need another one sooner. Not sure why people feel the need to shoot grit covered bullets down their new barrel :eek:
     
  3. jerkface11

    jerkface11 Member

    Joined:
    Oct 27, 2005
    Messages:
    5,499
    Location:
    Arkansas
    You don't use the Tubb lapping system on a match grade barrel. You use it on one that isn't shooting good to start with. While Mr. McMillan is certainly an expert on accurate rifles Mr. Tubb is hardly a novice.
     
  4. skinewmexico

    skinewmexico Member

    Joined:
    May 22, 2006
    Messages:
    2,621
    Location:
    West Texas
    Works great for moving your throat.
     
  5. mgregg85

    mgregg85 Member

    Joined:
    Mar 18, 2007
    Messages:
    2,008
    Location:
    Midland, MI
    I seem to recall reading a magazine article about this product, can't remember where. They used it on a rifle fresh out of the box, so you really couldn't tell if it helped or not.
     
  6. bl4ckd0g

    bl4ckd0g Member

    Joined:
    Nov 12, 2006
    Messages:
    362
    Location:
    Prestonsburg, KY
    Depends on what gun is being shot. Perhaps a Ruger or Remington varmint barrel that has been roughly cut. This kit is quite unnecessary on barrel that have been properly finished. Break-in is an excuse for gun manufacturers to skip a few steps in their barrel production process.

    I did not have to break in my CZ 550 nor Kimber 84M.

    Even so, you can spend a few bucks for jeweler's rouge and apply that to your existing factory ammo to clean out a rough barrel.
     
  7. birdbustr

    birdbustr Member

    Joined:
    Aug 21, 2007
    Messages:
    454
    Location:
    Sioux Falls, SD
    I used it on my new 7mm-08 Remington LVSF and then again on a slightly used (<50rds)Remington Sendero 7mm STW. Both barrels to seem to retain very little copper fouling compared to other rifles. The 7mm-08 seemed to break in easier than other rifles. I have no evidence of anything beneficial, all I can say is that I think the Tubbs bullets seemed to work in the beginning and I am going to keep using them at the recommended intervals. I don't see how it can hurt. It hasn't so far.

    7mm-08 2 rounds every 100rds and 7mmSTW 4 rounds every 100rds. It's supposed to prevent throat erosion and extend barrel life.
     
  8. SwampWolf

    SwampWolf Member

    Joined:
    Sep 18, 2005
    Messages:
    3,992
    Location:
    North Central Ohio
    Do these bullets do a better job "polishing" (breaking-in?) a bore than does a mildly abrasive paste, like J-B cleaning compound? How much do they cost?
     
  9. RugerOldArmy

    RugerOldArmy Member

    Joined:
    Sep 18, 2004
    Messages:
    915
    Location:
    Earth, Milky Way
    Final Finish grit-covered bullets? That stuff is almost as good as David Tubb's computer cooling and cleaning garden hose attachment. It works almost as fast too!

    I've got his sight alignment tool: [​IMG]

    He's a great shooter, and may have gone to the PT Barnum school of business.
     
  10. bl4ckd0g

    bl4ckd0g Member

    Joined:
    Nov 12, 2006
    Messages:
    362
    Location:
    Prestonsburg, KY
    More grit and detritus in the chamber and barrel will accelerate throat erosion.
     
Thread Status:
Not open for further replies.

Share This Page