Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Tumblers

Discussion in 'Handloading and Reloading' started by Cannon7mm, May 15, 2003.

Thread Status:
Not open for further replies.
  1. Cannon7mm

    Cannon7mm Member

    Joined:
    Apr 17, 2003
    Messages:
    19
    Which tumblers do you folks use? I was looking at the Lyman 1200 with auto-feed, but don't know if its big enough, or if I should go up to a larger model?

    Any thoughts?
     
  2. warrior23

    warrior23 Member

    Joined:
    Feb 14, 2003
    Messages:
    145
    Location:
    East Coast
    I have 2 Lyman 600s and just p/u the Dillon its their largest one.The tumbler is massive and works great.My Lyman 600s are still going strong had them for prob 15 yrs.
     
  3. Cannon7mm

    Cannon7mm Member

    Joined:
    Apr 17, 2003
    Messages:
    19
    So you would buy a very large one? How many rounds should it hold?
     
  4. Edward429451

    Edward429451 member

    Joined:
    Dec 24, 2002
    Messages:
    2,251
    Location:
    Colorado Springs Colorado
    I've been using Lymans big one (3200?) for a few years nowand have no complaints. Brass has a way of stacking up on you real quick so get the bigger one rather than the smaller one is my thought.

    I came home one day to find it not working at all. The fuse was good etc., and a call to Lyman was met with "no user serviceable access or parts inside, send it in with $80 and it'll be replaced". So I cut the plastic air vent panel off the bottom with a dremel and easily found the loose wire which had vibrated loose, slammed on a wire nut and its been problem free ever since.
    Thumbs up for the Lyman.
     
  5. P95Carry

    P95Carry Moderator Emeritus

    Joined:
    Jan 3, 2003
    Messages:
    16,341
    Location:
    South PA, and a bit West of center!
    The standard one from Midway - not huge but, I find it adequate for my needs ..... mostly rifle stuff is all I regularly tumble.
     
  6. HSMITH

    HSMITH Member

    Joined:
    Dec 26, 2002
    Messages:
    4,933
    I bought the Frankford Arsenal vibe cleaner from Midway a while back, the $40 unit. Works great, will hold 500 45acp or 400 223 easily, 250 7mm mag too. It is big enough for me, price was great too.
     
  7. Standing Wolf

    Standing Wolf Member in memoriam

    Joined:
    Dec 24, 2002
    Messages:
    24,041
    Location:
    Idahohoho, the jolliest state
    I have a small tumbler from Dillon that's worked just fine for four or five years, and Dillon's case polish does a good job for me, too.
     
  8. Sisco

    Sisco Member

    Joined:
    Dec 24, 2002
    Messages:
    2,775
    Location:
    KS
    I use the Midway also, always been big enough for my needs.
     
  9. Steve Smith

    Steve Smith Moderator Emeritus

    Joined:
    Dec 21, 2002
    Messages:
    4,394
    Location:
    Southeastern US
    No Lymans or Midways, please

    I have a Lyman but poster JC121 (my roomate) has one (maybe Frankford Arsenal?) that has a rubber drum. Makes ALL the difference. I don't like reloading when my Lyman is running, but that rubber one is SO quiet!
     
  10. Unisaw

    Unisaw Member

    Joined:
    Dec 28, 2002
    Messages:
    780
    Location:
    Pacific NW
    I use the Midway and have found it more than adequate for my needs. I reload for pistol only.
     
  11. HSMITH

    HSMITH Member

    Joined:
    Dec 26, 2002
    Messages:
    4,933
    Most guys here are talking about vibratory case cleaners, and the original poster asked about tumblers . They are very different.

    Steve, could you get a brand on the rubber drum tumbler? I have a vibe cleaner but would also like to have a quiet tumbler.
     
  12. Cannon7mm

    Cannon7mm Member

    Joined:
    Apr 17, 2003
    Messages:
    19
    How are they different?
     
  13. Steve Smith

    Steve Smith Moderator Emeritus

    Joined:
    Dec 21, 2002
    Messages:
    4,394
    Location:
    Southeastern US
    Good point.

    The difference...a vibe cleaner just vibrates. A tumbler has a drum that revolves making the media and cases (or rocks, whatever) "tumble" inside.

    This is a version of a tumbler: [​IMG]

    Note the rubber drum. These are usually made for polishing rocks so there is some thought that goes into making them quiet. A rock tumbler can run for a month before you change grits, so you want it to be quiet.

    The one vibe cleaner that my romate has also has a rubber drum.


    HSMITH...will do.


    BTW, I'm an H Smith too.
     
  14. HSMITH

    HSMITH Member

    Joined:
    Dec 26, 2002
    Messages:
    4,933
    COOL! And thanks for putting an eye on the tumbler for me.
     
  15. Guy B. Meredith

    Guy B. Meredith Member

    Joined:
    Dec 25, 2002
    Messages:
    2,292
    Location:
    Salem, Oregon
    I have one of the Thumler tumblers from Lockstockbarrel.com. This was recommended by the moderator of the old CompuServe Firearms Forum that got me off on the right foot. I never did trust vibratory cleaners as the off center mass has just got to be self destructing. I let the Thumler run a bit longer, but it is guaranteed quieter and, I trust, more durable.
     
  16. Steyr Hahn

    Steyr Hahn Member

    Joined:
    Apr 27, 2003
    Messages:
    33
    Location:
    Eastern North Carolina
    I have 3 of the Midway vibratory type cleaners the newest one being 5 years old, the oldest is getting close to 9 years. The only failures have been the wiring, right there where the line cord connects to the motor leads. A couple of minutes and a new crimp connector and once again it are the sweet sound of brass getting ready to reload.
     
  17. Arub

    Arub Member

    Joined:
    Dec 27, 2002
    Messages:
    188
    Location:
    Southeast Alabama
    I would think that the large majority of reloaders refer to 'vibratory' case cleaners as 'tumblers', so much so that the term has become generic for any case cleaner, tumbler or vibratory. I do thank you for the vocabulary lesson. Now I don't have to consult 'Word Power Made Easy' for todays lesson.

    I use the standard MidwayUSA 'Franklin Arsenal' tumbler (if they call it a tumbler, I call it a tumbler). Cost was about $40. It holds, per their catalogue, about 600 9mms, or equivalent. I usually run two to three hundred .357s or .40S&Ws through it at a time. Works well.

    Have also added the moly lube kit. Also works well. If you decide to do this be prepared for a lot of noise. I live in a turn of the century (last, not current) home, about 3800 sq/ft, built of heart pine w/1X4 tongue and groove walls. The 'tumbler' is set up in the back part of the house and you can hear, it loud and clear when moly coating, all the way up to the front dens, even with the doors closed.

    Lots of luck. There's a lot of good equipment out there. I don't think that you can go wrong with the Franklin Arsenal, RCBS, Dillon or any of the other major brand equipment.
     
  18. Steve Smith

    Steve Smith Moderator Emeritus

    Joined:
    Dec 21, 2002
    Messages:
    4,394
    Location:
    Southeastern US
  19. winwun

    winwun Member

    Joined:
    Apr 26, 2003
    Messages:
    225
    Location:
    Blount County in East Tennessee
    A significant aspect of tumbler v vibrator is that the vibrators are generally much more agressive, and therefore time-sensitive, subject, of course, to the type and condition of media.

    Due to the variables mentioned above it is difficult to make a definitive statement, but generally, an hour or so in a vibrator is about all you want to go without violating the integrity of the cases, whereas the less agressive tumblers can be run all night long to achieve the same results.

    I prefer the Thumlers tumbler on an all-night run, because it is in effect, "instant cleaning" because I can start it B-4 I go to bed, and the brass is pretty the next morning and i don't have to worry about setting a timer to avoid brass deterioration.

    I left a load of 9mm range pick-ups (I only have about 50,000, but I still pick them up) in too long, and they were thinned to the point that the rims would pull of in attempting to pull them out of the carbide resizing die.

    I tossed them.

    The type of polish you use also has something to say about it all. I have used, with some success, non-ammoniac car polishes.

    Nickle takes about half the time of brass.

    Media that is no longer viable makes fine "sandbags". Put it in a plastic garbage bag (small size) and tie the end and put it in an empty shot bag and get your bride to run the Singer across the end of the bag a few times. The plastic bag keeps the media from soaking up moisture in event of rain.
     
  20. ed dixon

    ed dixon Member

    Joined:
    Dec 25, 2002
    Messages:
    459
    Location:
    Ireland
    Huh. I hadn't yet heard that a long (+ one hr.) vibratory cleaning could actually degrade brass integrity. I've never let mine on all night but have done some three-to-four-hour runs just to play with it and see if a little more time got the cases a little brighter. This info surprises me for sure.
     
  21. winwun

    winwun Member

    Joined:
    Apr 26, 2003
    Messages:
    225
    Location:
    Blount County in East Tennessee
    Ed, as I said, there are so many variables, that it is almost impossible to make a factual statement about the issue. I was only recounting what happened to me.

    All things being equal, new media, new polish, same amounts of everything, then a vibrator type will clean quicker than a tumbler.

    Of course, cleaning equates removing surface. The machine isn't capable of removing just the stain, dirt and tarnish.

    Somewhere along the continuim you reach a point of notable damage to the cases.

    Nickle will stand "overcleaning" more than will brass.
     
  22. AZ Jeff

    AZ Jeff Member

    Joined:
    Jan 21, 2003
    Messages:
    821
    Location:
    Phoenix, AZ
    As noted by others, a viratory tumbler is more aggressive in cleaning cases, and it IS possible to "overdo" the cleaning.

    I solve this problem by connecting my tumbler to a household light timer, the kind you use to turn lights on and off when you are vacation.

    I set the timer up to allow the tumbler to run for 4 hours within a 24 hour interval. With old, dirty, media, this gives me clean brass in one overnight run, and I can turn down the "ON" interval with new media as necessary.
     
Thread Status:
Not open for further replies.

Share This Page