Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Wood blocks for mounting reloading gear

Discussion in 'Handloading and Reloading' started by dak0ta, Mar 10, 2013.

Thread Status:
Not open for further replies.
  1. dak0ta

    dak0ta Member

    Joined:
    Feb 14, 2008
    Messages:
    2,052
    Hi,

    Space is a premium here, so I was wondering what kind of wood, size, and thickness is best so that everything is stable when mounted to a desk. Your insight is appreciated!
     
  2. wild willy

    wild willy Member

    Joined:
    Aug 19, 2008
    Messages:
    374
    Are you using c-clamps.The wood doesn't need to be real thick if you use C-clamps big enough to clamp tight against the press. I use 2x10 for my presses for priming tools and trimmers 3/4 inch plywood
     
  3. matworz

    matworz Member

    Joined:
    Jan 23, 2011
    Messages:
    53
    I have a wood shop where I usually have lots of good scrap wood choices. I mount my presses on 1 1/2" thick oak hardwood and then clamp it to the bench with woodworking clamps. Nice and solid, though I doubt it HAS TO BE that thick.
     
  4. dak0ta

    dak0ta Member

    Joined:
    Feb 14, 2008
    Messages:
    2,052
    Yup I'll be using C-clamps. Ok, and what kind of screws, nuts, washers do I need to lock down a Rock Chucker and all the stuff that comes in the kit. Balance, Powder measure, Lee Zip trim.

    Should I mount each individual item onto a separate block or is sharing ok?

    Is ordinary plywood good enough?
     
  5. matworz

    matworz Member

    Joined:
    Jan 23, 2011
    Messages:
    53
    I like them all separate, so I can move them around when I need/want. It depends on your work area and how much space you have. I used the biggest bolts that would fit in the holes of my presses. For Lee press, I think that may be 5/16 bolts, maybe 3/8, I don't remember. For the press itself, I'd lean more towards the 2x material, 2x6, 2x8, whatever. You'll want to countersink or counterbore the holes on the bottom side. Not sure 3/4 ply will be quite hefty enough. Some may use it... I don't know.
     
  6. Otto

    Otto Member

    Joined:
    May 14, 2007
    Messages:
    1,393
    Location:
    Lone Star State
    Posting a photo of your desk would give others a better understanding of what you're trying to accomplish.
     
  7. ReloaderFred

    ReloaderFred Member

    Joined:
    Apr 28, 2005
    Messages:
    5,825
    Location:
    Oregon Coast
    I use 10" squares of 3/4" plywood, with 3/4" particle board laminated to the top, since I had plenty of both when I made them up. I recess the bottoms for bolt heads in the appropriate places, which gives a smooth underside, but the strength of the full size bolts. I use the biggest washer for the bolt size I can find for the underside, so the bolt won't pull through the plywood.

    I use expandable "C" Clamps for attaching to my bench. I keep all my lubrisizers mounted this way, plus other tools that aren't permanently attached to my benches.

    Hope this helps.

    Fred
     
  8. clocker

    clocker Member

    Joined:
    Jan 7, 2012
    Messages:
    72
    My first attempt was using 2x12 lumber cut into 12" sections. This worked ok, but I was never satisfied with the flatness since I don't have a belt sander or planer that large. I finally settled on 2 12x12" pieces of 3/4" ply laminated together. Each of these base plates has 1/2" holes drilled in four corners which match up with holes of the same dimensions on my benches. Why 12x12"? I have a number of presses and picked the smallest baseplate size where the press, accessories and handles would be within the footprint of the baseplate.

    The system works for my needs, but if you want to go for the ultimate in space savings and flexibility then check out some t-rails. Here is a link that should give you some inspiration http://ultimatereloader.com/2011/03/27/the-new-reloading-bench-system-at-ultimate-reloader/
     
  9. rondog

    rondog Member

    Joined:
    Jun 29, 2007
    Messages:
    6,788
    Location:
    Commurado
    Every person's needs and situation is different, there's no way you can get a solid answer or solution on a forum. You'll pretty much have to figure it out on the fly, which isn't hard. You may end up trying several things before you're happy.

    In my situation, I needed extra height, so I cut two pieces of 2x12, glued and screwd them together to make a 3" riser, then mounted it to my bench with four 3/8" carriage bolts. I then mounted my press to that with lag screws. Ugly, but very solid and works well.
     
  10. dak0ta

    dak0ta Member

    Joined:
    Feb 14, 2008
    Messages:
    2,052
    I think I got a good idea of what to do now, heading out to the hardware store :)
     
  11. Lost Sheep

    Lost Sheep Member

    Joined:
    Aug 16, 2009
    Messages:
    2,661
    Location:
    Alaska
    Welcome to reloading and thanks for asking our advice.

    I mounted my RockChucker on the end of a 2x6.

    I drilled holes to fit the hole pattern. I countersunk the underside so the heads of the carriage bolts would not stick out past the surface of the wood. Because of the countersink, the actual wood holding the press was really only about an inch thick

    Washers and wing nuts allow me to mount and dismount the press from the board easily.

    I used to stick the other end of the 2x6 into the drawer of an end table. Close the drawer as far as it would go and the press stayed put pretty well and was inclined back at a convenient angle. Sometimes, I just strapped the 2x6 to the top of the table (properly padded with a towel or newspaper to avoid scratches).

    Since the end table was not that heavy, I generally steadied the press with my left hand as I worked the handle with my right.

    Lost Sheep
     
  12. gamestalker

    gamestalker member

    Joined:
    Sep 10, 2008
    Messages:
    9,832
    Location:
    SW Arizona
    I have all but one time mounted mine using C-clamps. I quickly realized just how nice it is to be able to move things around quickly without having to hassle with removing bolts.
    I clamp directly to my hard wood table top. I have a very large oak table that I have clamped another very large and thick mahogany table top to. I did it like this to add more space to my work areas, and to add more weight so it nothing will wobble or flex . My entire bench probably weighs 250 lbs. or more.

    GS
     
  13. BYJO4

    BYJO4 Member

    Joined:
    Nov 28, 2010
    Messages:
    1,776
    Bonding 2 pieces of 3/4" plywood should give you both the strength and thickness that you need. I would use nuts and bolts to secure equipment and counter sink nuts and washers.
     
  14. 1SOW

    1SOW Member

    Joined:
    Oct 28, 2007
    Messages:
    4,106
    Location:
    South Texas
    My depriming-sizing press is mounted on a treated 2x10 and clamped to a B&D folding woodworking table.
    Steady as a rock
     
  15. Centurian22

    Centurian22 Member

    Joined:
    Dec 22, 2011
    Messages:
    1,233
    Location:
    Maine
    I mounted my LCT to a stand alone.... stand. Fits in a closet, corner or up against a wall when I'm done and is very stable and sturdy even when loading my .308 from the couch. Not the best picture but you can get the idea.

    [​IMG]

    Made from repurposed 2x3's, screws and a doubled up piece of 1/2" plywood (to make it 1" thick).
     
  16. Muddydogs

    Muddydogs Member

    Joined:
    Nov 23, 2011
    Messages:
    455
    I mount my presses with lag bolts to the bench so if I need to move them all I have to do is unscrew the lag. The trimer is mounted to a 2x4 and the swager is mounted to 2 1x2's stacked together they then get clamped to the bench when needed. My powder measure is on a stand that just gets clamped down when used.

    Everyone says that a press needs to be bolted down but I have found that 1/4" x 3 or 4 inch lag bolts ran through the bench into a 2x4 backer under the bench holds the press just fine and I have leaned on the old Rock Chucker hard a few times. My LnL AP is bolted down the same way. The bullet lube sizer and shotgun presses just get screwed down with deck screws and after 10 years I have never had a press work lose.
     
  17. Blue68f100

    Blue68f100 Member

    Joined:
    May 25, 2011
    Messages:
    3,189
    Location:
    Piney Woods of East Texas
    My portable set up uses T-Nuts that are counter sunk to secure the press, so it does not get in the kitchen table. The top is made of two 3/4" plywood glued and screwed together, with a protective pad (paper will do) between the top and press top if your doing this on some fine furniture. When you setup place the press over a table leg if you can to minimize load on the top. Then secure the with C-clamps at back and front and should be good to go.
     
Thread Status:
Not open for further replies.

Share This Page