Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Would you load em?

Discussion in 'Handloading and Reloading' started by BunnMan, Jun 18, 2013.

Thread Status:
Not open for further replies.
  1. BunnMan

    BunnMan Member

    Joined:
    Jan 5, 2009
    Messages:
    139
    It's been awhile since I took the Kalashnikov out but my daughter wanted to shoot it on our Father's Day range trip so I took it along. It's a Vepr2 in .223. I had maybe 100 rds. of 55gr loads including around 60 I built using a near max charge of Varget. The work up was shot through my AR and she tends to like em HOT, that's why they were loaded near max. The AR dimples the cases on the way out but not terribly. The Kalashnikov is HARD on brass though, especially the hotter stuff it seems. Kinda funny, you can tell the design is simply to sling out the old and clear the way for the new...very functional rifle. I'm not sure I should load these again after being kinked so sharp and deep...what do you think? If the answer is no, the Russian girl is gonna stay in the safe until bulk stuff gets ALOT cheaper!!! lol. I aint wasting my precious brass on her if she's gonna treat it this way!

    [​IMG]

    [​IMG]

    Thanks,

    -BunnMan
     
  2. Thompsoncustom

    Thompsoncustom Member

    Joined:
    Dec 21, 2010
    Messages:
    999
    Got some pics? One of the worst piece and maybe one of the best?
     
  3. BunnMan

    BunnMan Member

    Joined:
    Jan 5, 2009
    Messages:
    139
    There are two LARGE pics in the post...at least on MY screen...lol. Maybe yall can't see em?
     
  4. 32_d3gr33s

    32_d3gr33s Member

    Joined:
    Mar 17, 2013
    Messages:
    288
    Location:
    West Michigan
    No pics for me...
     
  5. BunnMan

    BunnMan Member

    Joined:
    Jan 5, 2009
    Messages:
    139
  6. Cosmoline

    Cosmoline Member

    Joined:
    Dec 29, 2002
    Messages:
    23,648
    Location:
    Los Anchorage
    Wow, that is some pounded brass. Personally I draw the line when I can see a line. A dent is no problem, but there's a clear line where the brass has potentially been thinned out and that would be too much of a risk for me. Maybe others have had better luck, but I don't think resizing fixes weak spots.
     
  7. 243winxb

    243winxb Member

    Joined:
    Jul 7, 2004
    Messages:
    8,654
    Location:
    Hopewell Big Woods
    Scrap brass. Try a reduced load. [​IMG]
     
    Last edited: Jun 18, 2013
  8. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    I would resize them and see what they look like then before making a decision.

    The location of the dent is not a safety factor as far as promoting a gas leak back through the chamber.

    They will fire-form back out completely when fired again.

    rc
     
  9. Bruno2

    Bruno2 Member

    Joined:
    Aug 3, 2009
    Messages:
    885
    Location:
    Tulsa , Oklahoma
    Shootem til they split!

    Chootem chootem!
     
  10. 45lcshooter

    45lcshooter Member

    Joined:
    Oct 6, 2012
    Messages:
    919
    Location:
    Central of the Commonwealth of PA
    if you have a bolt action rifle, i would at least resize them and see how they look, if they look good, i would use them for a bolt action on a low charge. In the pics those dents look a little deep to me to have a near max charge in again and put through a semi auto, until how they look resized. just my opinion
     
  11. raddiver

    raddiver Member

    Joined:
    Aug 11, 2010
    Messages:
    215
    Location:
    Louisville Kentucky
    not worth the risk

    FWIW, I personally would not shoot those.
    To me, that crease is just way to deep and sharp to try and reload.
     
  12. FROGO207

    FROGO207 Member

    Joined:
    Dec 7, 2008
    Messages:
    6,139
    Location:
    Mount Desert Island Maine
    Try and see where they are hitting on the receiver and cusion it there. That will help some, and I would try a couple with light loads and see if they work after a couple reloading cycles or do split there. IMHO 223 brass is not THAT expensive to just trash them if you are worried about safety.:scrutiny:
     
  13. steve4102

    steve4102 Member

    Joined:
    Oct 14, 2004
    Messages:
    2,439
    Location:
    Minnesota
    Try a faster burning powder than Varget and see if that helps.
     
  14. kerreckt

    kerreckt Member

    Joined:
    Apr 23, 2011
    Messages:
    788
    Location:
    SE Virginia
    I would resize and if they look no worse...load and shoot. They are not dented in a potentially dangerous place.
     
  15. sellersm

    sellersm Member

    Joined:
    Jan 20, 2011
    Messages:
    556
    Location:
    CO Rockies
    Veprs, like the PSL and some other semi-autos, are hard on brass, as you can see. I know some folks have had good luck with some simple mods (try Googling for them), and their brass comes out much less 'dented'.

    I'd see how they resize and give a few a try...
     
  16. GLOOB

    GLOOB Member

    Joined:
    Sep 16, 2007
    Messages:
    5,940
  17. blarby

    blarby Member

    Joined:
    Feb 25, 2011
    Messages:
    5,144
    Location:
    Calapooia Oregon
    Ahhhh, the VEPR brass....... I feel your pain.

    The worst I would not reload.

    I tried resizing some of the worst ones, and the best ones of my lot.

    The worst ones wouldn't even go in the die......

    The best ones resized, but still left far too much of a dent for my tastes.
     
Thread Status:
Not open for further replies.

Share This Page