Search results for query: *

My choice is 95gr FMJ and Speer GD's. I load them so that the FMJ is first out followed by a GD, and so on and so on. With a 13rd clip I don't really worry to much about expansion or penetration. I also load my own rds in both types of bullet. These are of course for SD. For practice I shoot...

gpr.... Now a member of this forum, thanks. sbs

I shoot at night, using headlights. Also, a Red Dot. Pistol I am using is a S&W M41, in .22lr. To all who have posted to this tread......Thank You....Much. sbs

Well lets see....Does it feed well? How accurate at say 50-75yrds. I do alot of jackrabbit shooting, and usually at these distances. And thanks Gary I will do that. sbs

Looking for info on PMR-30. I have been thinking on buying one, and would appreciate any info, especially from someone who has one or has shot one. sbs

bigmike45.... I noticed that you posted owning a KelTec PMR30. I have been looking at buying one, and would appreciate any info you might want to share about this pistol. sbs

Thanks folks. I think it will go to a gunsmith. sbs

Inherited subject shotgun. Single shot, break barrel. It's the breaking I am having trouble with. Frozen shut. Have tried all sorts of ways to open it, have oiled it etc. So far the only way I can get it open is to bang the barrel end on the floor, while holding the barrel release down. I have...

Again, thanks to all who have posted to my question. sbs

Thanks, madcap and thunder173. sbs

I want a crossdraw holster for a .38 SPL/4 inch barrel. Anyone have info?? please. :) sbs

M2 Carbine.... Good thing you don't live in California. They have a law that would put you in jail. I also reload in great quantity. So, I would be in the cell next to you. .380/9MM/.38 SPL .308/.300 Sav./6mm Rem/7Rem Mag/M1 carbine sbs

I carry a BDA. 14rds/13 in mag and one in the chamber. I train to start my shooting at 20ft./center mass. I also train at 8-10ft. with point of aim beginning at just under the chin and working up from there. I stack the rounds so that I get a start rd of FMJ followed by a HP. At the ranges I...

I find that reloading seems to satisfy some need I didn't know I had. I do most of my reloading in the winter. And, alot of shooting in the spring and summer. Loading in the winter gives me something to do when I can't get out. sbs

My Speer manuals indicates that USRAC made a rifle in .307, based on the Win. 94. Also, indicates that Marlin also produced a rifle in .307, 336 0f course. The manual shows loads for bullet weights from 100gr to 170gr. How much are they asking for the rifle pictured? sbs

GAM36....Is your 336rc new or used. I ask because I have had a 336rc since 1956. Mine has micro-groove. Was made in 1956 and bought in Alaska. sbs (OOPs, sorry folk. Can I join this tread with y'al?)

I agree and do conform with most of what I have read in the prior posts. But, I must ask the question: Why is it that a bullet made by two different makers, (with all dimensions the same, and SD's/BC's the same) cannot be loaded using say Hornady info vs. Speer, vs. etc.?? sbs

I looked at my Hornady manual,and find that it gives a start at 4.7grs of w231, col 1.070" with a max load at 5.6grs. (90gr HP-XTP) Are you sure that your powder scale was set correctly? Could be that you set it at a lower weight, or that the scale was not properly in balance, before you set...

Case trimming is the pits, in my Ho. Necessary but takes a lot of time. sbs

I think that the use of small rifle primers in any caliber requiring a small pistol primer, can be done, but I don't think I would try it. sbs