Yeah sorry I fat finger a lot on my phone so I apologize for that. But I should have my buffer back today as my father inlaw is making heavier weights for me to put in it will be 4oz when done and ill test it with the extractor upgrade and the heavier buffer!!
That's what I'm going to do. I have access to a psa and bushmaster bcg. So I'm going to try the heavier buffer and the upgraded extractor spring kit first and if I still have the same issue I'll try a different bcg
Do not know the gas tube just says mil spec 304 stainless black coated. The gas key is just a standard key nothing special that I know of and a low pro gas block.
I went with a dsa as it happened to be in the right place at the right time for the right price!! And as far as I know everything I'm the upper is a dsa even the bcg. When I purchased it the gas key and gas tube were best up (look like they hit at some point) so I replaced the key and the tube...
I tested the extractor and ejector and it would throw the brass about 2-3 feet away. So I installed an prong on the extractor spring (upgrade kit) and now it tosses the brass 5-6 feet away. I'm hoping with that and a heavier buffer (to slow the bolt down) it will cycle better. I know with 223...
To be honest I don't know what a bolt overpass is?? But when shooting 556 the bolt cycles so fast the brass either just falls out of the ejection port or it spins the spent brass in the receiver and when the bolt moves forward it will jam the spent round and the new round in the chamber. And a...
Well in usually stove pipe the ammo, but I noticed a few times the spent she'll just spun in the receiver that's why I said that. I will check the extractor yet again and gas rings. I dot think i have a gas leak as the gas system is functioning fine just not feeding 556!! It will feed 223 (as...
Yeah I have been looking at buffers mine has no stamps on it but my father inlaw has a machine shop so he is going to make me weights so I can increase or decrease it as needed to tune the gun in
all i know about the upper is that its a dsa 556 1/9 twist cromoly barrel. its a 16" upper with flash hider, and has a carbine length gas system (9 3/4" gas tube). i just put on a new gas key, gas tube and low pro gas block. but when shooting american eagle 556 green box (i think 62gr) the bolt...
i just built an ar15, 80% lower with a used upper. started out with cycling issues, and i saw the day i purchased it that the gas key and gas tube had hit several times and were beat up. so i replaced the key the tube and the gas block (only did the gas block to get rid of the a2 block/sight)...
I was just at a huge sprortsmans show in harrisburg pa.. and there was a vendor selling gunzilla, it is a gun cleaner/lubricant and said to be the cats ass... well i bought a small bottle of it (only $6) just to try it out...i have not used it yet but i was wondering if anyone is here has used...
all right yeah people were telling me the cases would swell up cause the 38 was a smaller diameter and a bunch of other ****.....i thought they had their head up their asses it didnt make sense to me and when i looked in the reloading manual all the specs are just about identical so i was...
ok so i am reloading my 357 well the dies are a 38/357 lee dies now i know the bullets are .357 for both 38/357 but i was told that if you shoot 38 through a 357 that you cannot reload them is that true????? and if so why not the dies are the same the bullets are the same........
I have 3 rugers....blackhawk .41mag, redhawk .44mag and a gp100 357 and they all have nice triggers all thought i really like the SA better the redhawk in SA has like a 2# trigger very touchy the blackhawk (only SA) is also very light i like them better than my smiths and dan wesson
I have been doing some long distance shooting and handloading some pretty mean rounds....but i was wondering about those rubber vibration dampeners that fit over your barrel of your gun.....they say it absorbs the vibrations in the barrel and improve accuracy...does any one have one and do they...
well is what my deal was is i have 100 interbond 150gr sp that i got when i bought my press.....i bought 150gr btsp....i was setting the press up with the interbonds as they were free and didnt really like them as a hunting load compared to the btsp......so i was wondering if i dial my scope in...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.