Search results for query: *

New XD45 Hi All, I purchased a new XD45 with four inch barrel in dark earth coloring. I have only had it for a week but, we have had some great weather here for shooting. I have 500 rounds through it so far and not so much as a burp. The extras they toss in come in handy too. The holster...

This is my favorite knife by far. I was very lucky recently and was able to get a hold of this very nice Jeff Chaffee Knife. It has a blued Damacus blade. The frame is titanium and the bolsters are brushed titanium with satin finish the sides are G-10. I hope you enjoyed the...

Strike marks Does every primer show a mark where it has been struck by the firing pin> I have an idea of what may be going on and it would be easy to check by looking at the parks on the primer or left and right of the primer. I am thinking that the method she is holding the revolver is...

I too understand LoadedDrum, I also understand that your intent was not to make light of the power of any weapon. If the only folks who ever read these messages were gun activist we would have nothing to concern ourselves with That is not the case thoough. To many states have fought a...

Bad name This is probably not going to be received very well but, I really dislike it when someone refers to a weapon as a toy. This tends to fuel the anti-gun folks with more out of context remarks. I was brought up from a small child that weapons or guns of any sort have one main purpose...

I Found this I would not have the nerve to take the picture. I found it someplace and thought it was interesting to say the least. Gary

Here is an Alaskan street gang and this is what I use on them. You have to let them swollow you and shoot them through the heart on the way down!!!!!!!!!! Gary

681 3" I have a 686 2 1/2" that is a real nice shooter but my carry piece is a 681PC with custom rear adjustable sites I have several holsters for 2 1/2" and 3" so I can't declare one that I use all the time. here is what I am carrying now it has smooth Ahrend grips on it. This is...

Try a M610 I think I would go to an indoor range that rents revolvers and try out a few different combinations. From what you are saying though I think I would go with the M610 and practice with some 40 S&W and then move up to the 10MM. I would get one with an unfluted 4 inch barrel and it...

Question for Newton What distance did your wife shoot at. I am not sure in Michigan where I qualified a score like that would have made it if it is 7 yards. We qualified at 7 10 and 17 yards and at all distances 50% of the shots had to be in the ten and nothing outside the 8. We had several...

Don't understand the concern I have a problem understanding the concern about the hammer snagging on something. First off no matter what revolver you have to carry concealed it should be in some sort of holster. I use a Mika pocket holster everday and have never had a lint or diry problem...

May Be Wrong I may be wrong but, it seems that 8 out of 10 complaints come from new guys who don't know there weapons well enough yet. I read of the new guys removing the side plates just to make sure they are clean we all know that is just plain foolish and usually more harm than good comes...

10mm I would go with the much overlooked 10mm . This is a well weighted weapon and has good velocity.without uncontrollable recoil. If you shoot the 44mag get plenty off practice dry firing and try to master controlling your flinch because once you shoot a hunting load the recoil will be quite...

couldn't stand looking at it Here is a better size picture Gary

686 cut down PC won't cut your 686 down that I know of. If they have a 3" barrel that will work they may exchange it though Go here and look under photo essay 4" conversion.http://www.sdmfabricating.com/. I also know a real fine revolver smith that cuts barrels down using SDM method his...

poor work That frame should have never made it through inspection. It is loaded with porosity (air pockets) and there is no way of telling how deep they are. Also the surface was never even polished or smoothed out. This is the worst case of quality control I have ever seen. Gary

High Ride Here is a hi ride holster but it is for K&L frames from 3 to 4 inches. Gary

also have a M637 and love it dakotasin I also have a M637 and I love itI have a couple holsters I really like the first is a pocket by Mika at http://www.frontiernet.net/~akim/ It is 15.00 and the best money ever spent. the other is a custom made by a friend. This one is $25.00...

I have been pricing it myself I have been looking into the same thing. I have a guy who does a great job and his email is: [email protected] Also there is a sight that shows how it is done and do a very good job http://www.sdmfabricating.com/ Prices will range from $150.00 to...

No lead I normally shoot all full jacketed bullets and don't have much problems with lead at all. It is a bit more costly but I just don't like lead Gary