Recent content by .45man

You guys have some great wheelies!!! Here is my FA .454 Premier Grade with .45Colt and .45ACP Cylinders Also are three S&W .44s (and my finger at the bottom of the mirror) Enjoy, have a safe and happy 4th!!

I shoot Berger 168gr VLD bullets out of a target .308 Varmint rig.....bullets are touching the lands......Walt Berger endorses this and provides load data too....

One other thing to do is mic the exit hole diameter of the cylinder. The exit holes should mic right at the same diameter or slightly smaller than the bullets you are shooting. If the cylinder exit holes are bigger than your bullets.......bingo!!...might need a new cylinder fitted. In any...

American Rifleman (comes with my NRA Lifetime Membership:D ) American Hunter (comes with my Liability Insurance through the NRA:D ) Guns (Excellent) American Handgunner (Excellent) Guns and Weapons for Law Enforcement (very good!) Handloader (great technical content for the reloader)...

Redneck, I recently purchased two (2) RRA .223 rifles. One for goofing around with my kids, and the other I use to target shoot at 250 yards. Let me tell you, I am very impressed with my target AR. Using factory Federal 80gr Sierra HPBT Match Bullets, I am able to put ten consecutive...

You guys have some great guns and photo skills.....We should all vote on the pictures submitted. .......I know some of you have seen this, but here it is again. I took this in my back yard. I took about 10 of them, and this one turned out the best. You can see some more gun pics here:

Carbon_15, I would strongly consider Nills. I have purchased three in the last few months and they are just outstanding. The fit is unbelievable.....so tight you would not believe, and the wood is nice....... I have one on a 629-4 (6" stainless round butt), 629-5 (4" stainless round...

JACKETED BULLET: Nosler 185gr JHP, 4.5gr Bullseye, WLP primer, Fed case, OAL=1.235" **1.2" @ 75 Feet, Very Light Crimp. OR LEAD BULLET Penn 200gr SWC-BB, 4.5 Bullseye, Fed LP primer, Fed case, OAL=1.215" 1-1/2" at 150 feet, very light crimp I realize these loads are a little warmer...

Ok.......since no one else posted......Here is some reload data for the 9mm and WST. Just open the spreadsheet and click on the 9mm tab at the bottom. CLICK HERE Best wishes!!!

platemakers, Hey....welcome to the club.....They are great guns and will last forever at .38Spl pressures...... Here is my copy: here and here Anyway, about the reloads, mine shot better with a little bit zippier load than the normal 2.7gr of Bullseye under a HBWC. Also, my 52 did not...

Nice shooting. Now take it out to 250+ yards. You will really see how well the gun, ammo, and shooter's skills are combined to maintain shot placement. All the best!!!

ernierod, I have several mild 9mm loads that work great in a 92FS and P-35. Check them out HERE: Just click on the 9mm tab at the bottom. Best wishes!!

YodaVader, Re the Leupold VX-III 8.5x25x40 AO scope, the clarity is excellent. I purchased my first one in 1999 and mounted it to the Winchester M70 .308W seen in the link in my previous post (to the far left). The 40mm objective mounts lower on bolt guns, but on an AR, that is not such...

I recently purchased a RRA Varmint 20" job, see the recent post on my evaluation of shooting it at 250 yards. http://www.thehighroad.org/showthread.php?t=223852 For quality and price, go with the RRA.....I was initially skeptical and had originally thought if the rifle was not good enough...

YodaVader, I hear you on the cost of the scopes......One thing you may consider, is purchasing a used scope off Goingbroker.com or Fbay.com I recently purchased a used Leupold VX-III 8.5x25x40 AO from Fbay.com for $520.00...... I had an agreement with the seller to evaluate it for three...