Recent content by CBP

Just downloaded Gunlog SPC to an Ipad. Have to say I'm very impressed with this software. Thank you, you've done an excellent job.

I'm back on the forum after about an 11 year hiatus. Can't believe it's been that long and I actually remembered my username and password. Still shooting and have the opportunity to pass the thrill of shooting unto my two daughters. They enjoy going to the range and blasting through dad's...

I just got back from hunting groundhogs and wanted to share an excellent load that I worked up for my rifle. I developed this last summer, but didn't get a chance to see how it worked at long range until today. The crops were too high on the farm that I hunt to test it last year. Here is...

And in less time than it takes to get my dies adjusted RC comes through with the load data that I need. :p Thank you very much sir. I have the Lyman 48th manual, but it doesn't have that bullet weight. The Lee reloading manual and handloads.com are right in that ball park as well.

Thanks guys, I was pretty sure that the dies were suitable for 32 H&R Mag. Appreciate you taking the time to verify it. I'm loading up some 100 gr. RN from Missouri. Have Unique, W231, and HS-6 powders. Chime in if you have a favorite charge for one of these powders. None of my sources...

I ordered a set of dies to reload 32 H&R Magnums for my brother. I had actually purchased a set of new Lee carbide 32 S&W Long dies from Midway. Can I use this set of dies for the 32 H&R Magnum? On MidwayUSA, I see that RCBS, Hornady, & Lyman all list the same dies for 32 SW and 32 Magnum...

I purchased an RCBS 2 die set for my 6mm Rem. I set the dies in my Lee Turret press the other night and ran a test case through the full length resizing die. Next, I trimmed the case to length and chamfered the inside and outside of the mouth. Since this was a test round, I didn't add the...

Put your finger under the metal arm when it is entering the shell holder. It that helps it to go in smoothly, then you simply have to put something in the grooves on the base of the press where the primer arm makes contact. The problem is that the arm is not completely vertical as it is...

Two good sites: http://www.handloads.org/loaddata/default.asp?Caliber=9%20mm&Weight=124&type=Handgun&Order=Powder&Source=Winchester http://data.hodgdon.com/main_menu.asp

Walkalong, No problem, I know you provide a lot of information to many posters on this site and I appreciate your dedication. Someday I will have the experience to help others out as well as you, RC, and so many others do. But that will take time and dedication on my part. I don't post...

Okay, thanks for the answer on using the regular primers. I appreciate it. Sorry if I sounded a little cranky in the second post. I understand that things can go off topic on forums. Now that the question was answered, I'll veer off myself. I keep all of the powder in a drawer in my...

Okay, I've edited my first post to keep the discussion on my main question. I am currently using CCI primers. I have mostly small pistol primers and a few magnum small pistol primers. Do I need to use Magnum primers with HS-6 powder when loading .357 or can I stick with the regular small...

Question on those familiar with HS-6 for .357 magnum. Should I use the standard pistol or magnum primers? I just opened up a can and loaded up 3 rounds using 158 gr. lead SWC. Checking Hodgon's online site and my Lee reloading manual, there was no reference to the type of primer. So I made...

I've read about the vinegar and peroxide trick for cleaning the lead from barrels and cylinder, stainless steel guns only if I remember correctly. It does work nicely to get the rings out of the cylinders of my revolvers. Cap one end, pour in the solution, and you can see debris floating to...

Take a small piece of steel wool wrapped around the cartridges and give a few twists. That might do the trick.