Recent content by ken grant

Untreated Corn , 50/50 mix Nu-Finish /Mineral Spirits and a small handful of steel BB's. Media gets dirty , use a magnet to fish out BB's and reuse them in new media

Look for a Propper 180 (Link); it's essentially a Wilderness belt (two layers of scuba webbing, five rows of stitching) with a 'normal' buckle. Much less obvious, IMHO, than the Wilderness buckle. As a bonus, it's reversible, and can be found on sale for ~$10; the last two I bought (I have...

Only one answer !!! A Dillon 550B. Can be used as a SS, can be used as a Turret except you move the case instead of the dies. No TINKERING needed. I used to have a 650 and a 550B but now only have 2 550's. One set up for Large Primers and one for Small Primers. Not really any trouble...

I have went to a trigger guard holster and AIWB although I have many other holsters. There several makers out there but most seem to be the same except for the Raven Vanguard 11. Most are just formed Kydex but the Vanguard is molded of some type of plastic

You are using a Spring Loaded Bearing for a non loaded chamber indicator extractor with a loaded chamber indicator extractor? YEP!!!! Cured my ejection problems with my 19. I have a 26 that ejects to my face but only on the last rd. with nothing in the magazine. Just weak ejection...

Gen.3 Glock 19----BTF,top of head,forward, left,right forearm. Polished extractor----no change Replaced extractor--- no change New plunger spring--- no change New extractor at GSSF match---no change 30274 ejector----- BIG CHANGE!!!! But not 100% Spring Loaded Bearing--- replaced...

I recall a magazine article in the late 50's on how to measure a 5 groove barrel. I don't recall the details but it used a lead slug, a caliper and a v-block. That where the P17 over sized bore came from. It also said that un-used .303 barrels left over from the P14 rifles were used until...

I seem to remember that the standard 5 groove .303 barrel was used but chambered to 30/06 which resulted in an oversized bore. Also Remington did the same with their M30 and M30S (IIRC) Another recall(I think) was that Eddystone 1917's had headspace problems and would chamber a no-go...

Story of my Gen.3 19 ejection problems Polished extractor----no change Replaced extractor---no change Glock match--let the guys check it and replace extractor(my request)----no change Replaced extractor plunger spring-----no change Installed a 30274 Ejector----BIG CHANGE but not 100%...

Luv .22's. 77-22 10-22 (2) GSG 1911-22 22-45 Ciener Conversion for 1911 AA Conversion for 1911 AA Conversions for Glocks (4) Ciener AR15 Kit M261 Military Kit for AR

5 AA Kits and they all work great with Rem. G.B. H.P. and Mini-Mags but not so well with anything else I have tried.

I had a Colt Officer's that I bought used. It would hardly run a mag through with out a jam of some kind. It had been sent to a top rated custom builder and a reverse plug recoil system, barrel(builder's name on it) and bushing installed. It came back and would not run and was sent back again...

I replaced my G19 and G26 with a 17 Trigger bar and did the same on my 23 and 27 with a G22 Bar. No problems at all and none had the bump on the bar. All of this was done in the last few months.

Airsofts Love the good AirSofts. Really serve a purpose in my life. I have worked with kids,old people,ladies and anyone else who wanted to learn how to handle a pistol plus a lot of training for myself. I use Glocks and 1911's and have really good Airsofts that match them really well...

I forgot to add that I also treated them to a 2 day Appleseed shoot 4 yrs. ago. I shot an M1A, Son my AR and Grandson a 10/22 with Tech Sights. At my age I got tired Sunday and my Son took over the M1A , Grandson took over the AR.