Search results for query: *

Another vote for the CZ-82. Better capacity, useable safety, nice trigger on most of them. I think it is the best of the combloc options out there. However, I still need to get a PA-63 to see how that compares, so that may change my mind but I don't think it will dethrone the 82.

If it hits the ground I let it go, with my luck the one I find will be the opposite of what I am looking for and I'll find a new way to make my life hard.

I would look at other options; take down "safes", cages, etc. I have bought (and left) a few safes over the years which is why I would look at other options. As HSO pointed out, most don't do a lot (aside from weigh a lot) and if you're trying to keep the average person out other options do...

Did they perform well? Yes, I would check my brass but that is down my list of concerns. Seems like your SIG may need a bit hotter of a load or a different powder. Nothing I would be worried about if the round performed as it should.

My jug says Made in USA, that is all I know.

I haven't looked at the Obsidian but do read the details on the rating; barrel length, pressures, etc. It may be fine (don't know) on a 22in with Trapdoor loads but NOT fine on a 16in barrel shooting Buffalo Bore through it. Ran into that with others in the past, need some barrel length to get...

The HP bullets may be too short for the magazine and causing your issue. If it runs fine with ball ammo, then you could look at putting a spacer in the rear of the magazine if you are determined to shoot HP out of it. May also want to check your spring tension and a few other magazines to see...

Neat! Very good idea. Much better than my current method of putting them into a tray and scanning with a magnifying glass.

I have a little net which goes over my hand. Was $15 or so and works pretty well.

Lipsey's runs aren't like a 365, they tend to only make so many of a model. Unlike Sig who will keep cranking out a model. Now, it will be interesting to see if S&W makes something like this down the road, or a similar version. Hard to say, I'm not sure what sort of agreement they have...

$660 is a smoking deal! I got the 32 version for $730 (plus tax) and was happy with that. Still waiting my 2 weeks so don't have it in hand yet..........

The rifle rods were worth it for me. Sometimes use socks (not on the rifles) but not loving them.

The new Ultra Carry j frame collaboration between Lipsey and S&W impresses me. Can get it in 32mag if you want something less common, but plenty of holsters for J frames out there. I am interested by the FN Reflex as it has an internal hammer rather than a striker. Same small platform with...

It could be normal for a "springer". Do you have other buddies who have a springer you could shoot? May let you know if it is sounding normal or not. They do make some noise. Can be tuned to reduce it some (if it isn't broken as mentioned above, but given its age I would not expect that)...

Not familiar with this and am not a business guy, so please excuse my ignorance. Is this an instructor/firearms thing or a thing aimed at LLC's and corporations, regardless of their type of business?

I have looked at them in the past but never bought one. Buddy and I were talking and I don't think either of us would buy a gun "safe" again. If I did, it would be the take down type like you are looking at. There are a few other makers which have a design like that also if you opt to go that...

Good on ya!

That is a huge bummer. Hopefully, they make it right FAST and you can enjoy it when it comes back. Give it some time for the disappointment and anger to fade. I have had a few of these deals over the years and often I can enjoy it after a bit of time. The older Colts speak to me. That QR...

Seems SIG hired away several key people from True Velocity to give them information to allow them to make the ammo for the new military contract. https://finance.yahoo.com/news/true-velocity-sues-sig-sauer-180351916.html

Thanks. Not competing. I am looking for something suppressor set mostly that I can put a dot on for my old eyes. Yea, some of their color options are going to be a bit hard to sell. That said, I do appreciate them doing it as they are going to coat it so may as well make the buyer happy...