Quantcast

Search Results

Search Again
Page 1 of 96
  1. Salmoneye
    Post

    Reloading Quandry For 1894 Marlin In .44 Magnum

    My 1894's absolutely love these jacketed bullets at .431"......
    Post by: Salmoneye, Aug 20, 2019 in forum: Handloading and Reloading
  2. Salmoneye
    Post

    Oiling of stocks

    Bingo. If you wait a sufficient time between coats, BLO can not penetrate any deeper once it seals the wood... That's the entire point of a...
    Post by: Salmoneye, Jun 11, 2019 in forum: General Gun Discussions
  3. Salmoneye
    Post

    Oiling of stocks

    Cosmo when fresh has a volatile hydrocarbon carrier that allows it to soak deeply into wood... Here is a test a guy did on soaking Hickory in...
    Post by: Salmoneye, Jun 9, 2019 in forum: General Gun Discussions
  4. Salmoneye
    Post

    Oiling of stocks

    That's the gist of what I said...The minimum time between coats in 'my' adage is 24 hours... Your way is saturating the wood too quickly...
    Post by: Salmoneye, Jun 8, 2019 in forum: General Gun Discussions
  5. Salmoneye
    Post

    Oiling of stocks

    Three drops at a time and then (bare) hand rubbed as far as you can go before applying more, hardly 'soaks' wood... Straight BLO dries (sort of),...
    Post by: Salmoneye, Jun 8, 2019 in forum: General Gun Discussions
  6. Salmoneye
    Post

    Oiling of stocks

    The old adage I was taught nearly 60 years ago for applying BLO on wood goes like this: One coat a day for a week, One coat a week for a month,...
    Post by: Salmoneye, Jun 8, 2019 in forum: General Gun Discussions
  7. Salmoneye
    Post

    Blue dot in 357 mag

    Remember... Alliant specifically recommends NOT using Blue Dot with 125 grain bullets in .357 mag, and not at all in .41 Mag......
    Post by: Salmoneye, May 6, 2019 in forum: Handloading and Reloading
  8. Salmoneye
    Post

    30-30 is it still being used today or am I the only one still using it?

    My Marlin 1893 built circa 1912 still takes a walk or two in the deer woods every year... It only gets mid-range cast loads for that duty......
    Post by: Salmoneye, Apr 24, 2019 in forum: Rifle Country
  9. Salmoneye
    Post

    How Popular Are CCW Classes Becoming Where You Live?

    No course requirements in Vermont, so few and far between for 'classes' to take...
    Post by: Salmoneye, Apr 24, 2019 in forum: General Gun Discussions
  10. Salmoneye
    Post

    Please help me out with this 44 leading issue

    IMNSHO, the best answer is paragraph one of post #17...
    Post by: Salmoneye, Apr 17, 2019 in forum: Handloading and Reloading
  11. Salmoneye
    Post

    Second Hand Grips worth anything?

    My 686-3 came with the same combat grips, and no...They are not for sale... I have seen them sell on the Bay anywhere from $175 to $400 depending...
    Post by: Salmoneye, Apr 10, 2019 in forum: General Gun Discussions
  12. Salmoneye
    Post

    Another Blast from the Past...

    So get a GP with a short underlug... I did...
    Post by: Salmoneye, Mar 30, 2019 in forum: Handguns: Revolvers
  13. Salmoneye
    Post

    What is your most unusual/oddball handgun?

    S&W .35 Auto (aka Model 1913) [ATTACH]
    Post by: Salmoneye, Mar 23, 2019 in forum: Handguns: General Discussion
  14. Salmoneye
    Post

    Why are so many more 44 Mag Blackhawks made in Plow than Bisley handle?

    You aren't alone... I am not a fan of the way the Bisley feels or recoils...
    Post by: Salmoneye, Mar 14, 2019 in forum: Handguns: Revolvers
  15. Salmoneye
    Post

    .30-30 and IMR 4227

    My Marlin 1893 loves 15gr of 4227 under a 165gr cast bullet...
    Post by: Salmoneye, Mar 11, 2019 in forum: Handloading and Reloading
  16. Salmoneye
    Post

    Accuracy issues with Remington Model 742

    Dad's 742 in .30-06 was a deer slayer that never wandered...But then, he never fired many rounds, and never more than enough to verify scope zero...
    Post by: Salmoneye, Mar 11, 2019 in forum: Rifle Country
  17. Salmoneye
    Post

    New Model Super Blackhawk Screws

    None of the screws on my Blackhawk/Super Blackhawk have any thread locker on them... Have not had a problem in 30+ years, and I am not exactly...
    Post by: Salmoneye, Feb 21, 2019 in forum: Handguns: Revolvers
  18. Salmoneye
    Post

    Using buckshot to create round ball loads in .32 SWL

    I use .310" round balls (#1.5 Buck) in .30-30 and .30-06 'Cellar Loads', and I use .360" (OOO Buck) in .38S&W, .357 Mag, and .35 Remington...
    Post by: Salmoneye, Feb 17, 2019 in forum: Handloading and Reloading
  19. Salmoneye
    Post

    Is it obligatory to have your CCW permit on your while armed in your jurisdiction?

    Vermont = No Vermont does not require a permit to carry openly or concealed, so there is no permit to carry...
    Post by: Salmoneye, Feb 13, 2019 in forum: Legal
  20. Salmoneye
    Post

    Do Not Shoot Lead Bullets Through any Glock Handgun See Below

    I fired thousands of cast bullets (remanufactured & reloads) through a G19 back in the early 90's before the interwebs told me that I was going to...
    Post by: Salmoneye, Feb 9, 2019 in forum: Handloading and Reloading
Showing results 1 to 20 of 1,906 Next >
Search Again
Page 1 of 96
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice