Search results for query: *

I am using clays in 4.6 grains under a Lee 200 grain RNFP bullet.

I am also using 3031 in 29 grains under a 180 grain RNFP cast , gas checked, powder coated, bullet and estimated to be about 2000 FP

What do you grind twice? I grind deer on medium and to the freezer. It stays that way for bologna and cooking. I only fine grind again for venison bacon and sausages. I love the big bite. I cut shoulder and neck in long strips and drop it in the throat of the grinder and it does the work with...

Old farmer wife told me they used to have a window box for a bird feeder with an inside and outside door. When starlings were in the box they shut the outside, opened inside and dispatched bird. Saved breast and make starling or black bird pie. They let the other birds go. Another old lady I...

I have an 1858 pietta with an 8" barrel and a 45LC conversion cylinder. Not a concealed gun, but I can stay on a pie plate at 40 yards and could probably still hit anything at 60 yards. We have two Glocks and a p365 and I no where near have the confidence shooting them as I do with the single...

$99??? I'd buy every one one of them and resell them on ebay!! The website says the big bite are $379. The cheaper one is $219 I use the #12 because I wanted the mixer and added an fine grind plate for making venison bacon and fine grind make better ground jerky. I don't partial freeze unless...

I am in my office and have 6 in here with me. Someone was talking about Americans owning more than one gun on teams call. They said they own one, two or three and I was like, I got more in this room with me that y'all own! :p I don't worry about locking most up as I am almost always home, work...

I made this one from a piece of a farriers rasp. I have a smaller one and these are my skinning/butchering knife. Cherry Burl for the handle.

I used this for the kitchen pantry closet and these hold A LOT of weight and ammo can add up fast. So does canned food and full ball jars.

I orders 6.8 SPC brass the Monday before thanks giving and they just contacted me last week as the credit card could not be held that long. It should be delivered Wednesday! Ordered 11/20/23 to delivered 4/10/24 and that is almost 4 1/2 months. I ordered 200 on ebay as I couldn't wait that long.

About 6' of rope and 14" of closet pole in my back pack. Then I call my Uber to show up with the ATV or Mule.

I will not shake and bake powder coat unless the humidity is under 40%. Static is not generated in high humidity. I have also had some powders fail and I am not sure if they were packaged in high humidity or not. I bought Eastwood lime green and works great. Bought Grape and I can't get it to...

I had purchased two PSA Uppers and they work, but I have had trouble with both. First one was 556 and had some jamming occasionally. Second one was 6.8 SPC and that one would not cycle anything. Took it to an Armorer I know and the Carrier Key on the BCG was out of spec and accepted the Red key...

Did you all get some powder that just will not work, or stick? I got Eastwood Hotcoat Lime green that works great. Grape would not stick. Don't know if its the powder, they got moisture in it. I am on cast boolits, I just don't post over there much. Might ask there, or search. I have had zero...

Does anyone maintain a list of powders that work for shake and bake coatings? I pretty much only try to coat bullets when it is 40% humidity or less in the house. I have Orient Red from powder by the pound and that works. Eastwood Hotcoat Lime Green and that works great. I bought Hotcoat...

I got an old Wesco dehydrator that I upgraded to a Meat one for jerky and still don't use it like this. The pins get "washed" every time I wash some cases. Little soap and a little lemon powder. Fluffed on a drying towel and laid on another get the water spots off the cases. That the worst...

I just roll them around on a towel and dump them on a towel in the family basement floor to air dry. Works great with wood stove or air conditioning running. I would use the linked hydrator and not use it for food also. Also, y'all dry your pins also? I leave the lid off my tumbler and let them...

I have been thinking about something like this also. I could make a table top like this. Make with with plywood and weld 1 1/2" EMT conduit to plates to attach to the table and use 1 1/4" EMT to slide into that and be the legs. I have been using fold up tables and lead sled or not, you just move...

147 grain cast on top of 3.6 grains of N320. Round nose for Targets and HP for load up mags.

I have a supply on the shelf running out, but I plan on mixing the first one when I can get some tin. I saved the below info and made a Excel sheet calculator to do the math. 91% pure lead, 9% tin leaves you with 10.5 bhn and water quenched maybe 14 or better. (to make 20# use 18.2# of lead and...