Search results for query: *

Update: Lee sent a new (plastic assembly), which was very easy to install and now my UTP with the 6 hole turret is running as it should. My range partner and usually average 100 rounds every other week, and I have plenty of time to reload [even at 6 strokes per round] to be ready for the next...

If you like work lights on your press. KMS² has one for you. Their website is also very helpful, it has the measurements for each product, and the RCBS Rock Chucker Pro 5 & 7 kit will fit the new Lee Ultimate Turret press. Check them out...

Short update: I found another shell holder and it is a little different so I installed it and it seems to work a little better. I am waiting for USPS delivery of the updated #19 shell holder either tomorrow or next day. I will update again then.

Now there is a question than I cannot answer for sure. Most everything that I have had or currently have has been Lee, however there were a couple of RCBS presses. I will root around in my 'spares' container and see what I can find. Thanks again for the suggestion.

I tried your suggestion and it seems that 'joining' is as it is supposed to be. The more I use it the better it gets, it is probably a wear in sort of thing, plus I have a set of jewelers files ans have been slowly smoothing all of the wear surfaces. Thank you for your help.

Short update: I have ben smoothing the lower part of the 'tang' of the primer arm that rubs on the back of the ram and things are improving a little bit.

I've been working on my new UTP priming. I have smoothed the edges of the primer arm, the sides of the slot and it is getting better, after watching it closely I see that the top of the cup is hitting on the bottom of the shell holder and preventing a full return to the 'open' position. The...

Good morning everyone, I have been a Cast Turret press user for many years, I just received the Ultimate unit and have it set up and loading 9mm Luger. everything works fine except the primer arm, It wants to stick and not come out of the ram sometimes and it also spits primers out on the...

I am curious, Lee suggests STP or grease to lubricate the turret, which do you suggest? Thanks

Just a note for you, I too have the LCT and run the Lee Bullet feedeer on it and it works great. Seat and crimp with the Lee seater die, (like before there was s factory crimp die).

What did you lube it with?

Did 10 Custom 30-06 rounds for having fun at the range, as soon as it quits raining

I have been using Lyman's Reloaders Data Log for many years, The only thing is, I forget to put the results from 'Range day', but I do save my targets or photograph them and recently started using 'Reloaders Workshop' (still learning all of it) and I can record targets in there. It is kind of...

For those of us that use powder coated lead bullets, sized to .356, will this system work? Thanks

Thanks for the reply

Thanks for the reply.

My primer shute agitation pin moves in and out slightly. I have pushed back into place a couple of times. What would happen if I put a little drop of super glue on it to keep it in place? I am hesitant to do this because of the proximity to the primers. I do not want to plug anything up.

Well now I have a real problem, I am out of bullets. So out to the casting, powder coating table in the garage and get busy. After getting all the updatied parts installed my SPP is running perfectly. I am waiting on the new primer pin just to have it (just in case). I need to bone up on...

New Help please: i have a powder check die in station #3. If I move the powder dispenser to station #3 ( i have used the Lee Auto drum long enough to totally trust it), to avoid spilling powder down on the primer pin, is there anything I can use station #2 for, or just leave it blank?

Help please: i have a powder check die in station #3. If I move the powder dispenser to station #3 ( i have used the Lee Auto drum long enough to totally trust it), to avoid spilling powder down on the primer pin, is there snything I can use station #2 for, or just leave it blank?