Search results for query: *

  1. L

    M1 Carbine reloading

    I also have to trim mine after about 5 reloads, sometimes less.
  2. L

    casting .45 ACP\LC

    The Lee 230 grain truncated cone in tumble lube version would be a perfect compromise. Feeds great in a 1911 and you could crimp in the top lube groove for 45 colt. Plus that flat point can do some serious damage!
  3. L

    Primer choice for M1 Garand

    Regular CCI large rifle primers is what I always use.
  4. L

    Three New IMR Rifle Powders!

    IMR4166- My big question is will this be in the "Garand safe" powder selection. If so, then I may just have to get some.
  5. L

    45acp bullet change & chambering issues

    +1 for the plunk test.
  6. L

    Reloading for .30-06

    My go to load is 165 gr Hornady with 57 grains of AA4350 if my memory serves me correctly. It's ridiculously accurate from my Savage.
  7. L

    Reloading for .30-06

    Double post
  8. L

    Mosin M38. An offer I couldnt refuse

    Nice. I have one in similar condition dated 1944. Its literally a blast to shoot!
  9. L

    Will be casting soon.

    I've been casting range scrap for my 1911. Its pretty soft like around 10 bhn and I can go about 200 rounds before it needs a good cleaning. Leading isn't horrendous, just get a good lead remover like shooters choice and the barrel will be shiny again in no time. Also I dont own a thermometer...
  10. L

    Best tool for removing crimped primer pockets

    +1 for the RCBS pocket swager. Cheap and it works!
  11. L

    Trouble with 45L/C

    Could some sort of oil or lube gooten into the primers or powder? It could be low pressure but that discoloration may be a hint of something else. 6 grains of bullseye should get a bullet out of the barrel.
  12. L

    A Question For Casters

    A six cavity mold of tumble lube design so that sizing could be skipped would be the cheapest and fasted route. Set aside a nice evening a week and make a couple thousand bullets.
  13. L

    Ramshot TAC in .223

    Grab that X-terminator! That's my favorite powder for .223 and 55 grain Hornady FMJ. It has a faster burn rate than TAC and many people haven't caught on to it yet. My AR-15 with a 1/9 twist loves that powder bullet combo. I can't remember the exact powder charge but it's close to the max...
  14. L

    Unexpected results with lead bullets

    I also second the theory of your barrel diameter being larger than your cylinder throats. Your cylinder is probably swaging your bullets to .357 and your barrel may be slightly larger. Time to find you a fishing sinker or a pure soft lead bullet and find your bore diameter. If it's larger...
  15. L

    2 to load 1 to shoot

    Zulu is the first thing I thought of, although they weren't muzzle loaders in Zulu, it would probably still be effective if they were.
  16. L

    Traditions Hawken kit gun, good for beginners?

    I guess it would depend if you got a good specimen or not on how much work needs to be done. I'm still on the fence, but I may just end up buying a finished gun after hearing all of this. Any more thoughts on .50 vs .54?
  17. L

    Traditions Hawken kit gun, good for beginners?

    Well damn...I was hoping for maybe some wood fitting, sanding, and bluing. All of that sounds like work!
  18. L

    Traditions Hawken kit gun, good for beginners?

    I cast my own bullets so the cost of components isn't a big deal. I guess it would come down to what my wallet finds better as far as caliber. I just don't want to booger up a kit gun and throw a few hundred dollars down the drain, but the idea of making my own is very appealing to me.
  19. L

    Traditions Hawken kit gun, good for beginners?

    So want to get me a muzzleloader and I found a Hawken kit in .50 cal for $315. I could try to build one or just buy one for $389. I kind of like the idea of building my own. My question is how much work is it to build one? Should I go .50 cal or .54? This will be strictly a range gun.
Back
Top