Search results for query: *

I was having bad problems with 454 rounds unseating and bought a Lee factory crimp die and it solved the problem .

I bought the 16" Noveske lightweight barrel and paired it with an upper and bolt from BCM . That thing shoots sub minute with 69 gr sierras. I'm buying an 18" from them next pay day! Very satisfied customer here....As was said though you can’t go wrong either way.

Yes ,I have two eight pound jugs of H335 ,some varget,and also H4895 . Just looking to see what others have found works good .. Thanks

where did you get SS media ???

Got 1000 55 gr midway dogtown at a garage sale and am looking for a good load . Shooting them in an AR-15 ..Thanks

Just bought a bravo 1 ss . All I can say is NICE ! They make some nice knives over there , top shelf in my book. Got a hunter and a skinner on the way now hahahahah:D

Yup, rusty chamber ..........Thanks

My neighbor has a rem 742 that will not extract spent cases . Must be something wrong with the extractor im guessing but we cant figure out how to remove the bolt . Anyone know how to get it out the RIGHT way ??..... Thanks

The issue is in the dbl action mode . Seems as though it's caming over something about 1\4 inch into the hammer stroke . I don't get it ,removed burrs and polished , new springs ect.... I cant pinpoint where it's coming from . Any help would be appreciated . Thanks Mike

While we are at it maybe you guys can direct me on how to get the bottom latch to stay open longer so as not to leave that ring around the cylinder ?? Thanks

Thanks Badger . I got the one from Brownells in today but it says it needs fitting by a smith. Is that just a CYA on their part and it just drops in ?? I tried to measure the old one from the pin to the top of the paw but it's hard to get an accurate reading . They seem very close . What do you...

I have a 357 Blackhawk and would like to make the cylinder spin both ways for ease of loading . How do I go about this??

Ok so how do I remove the single action capabilty ??

The problem was there when I got it . The filing was done to try and take the rounded edge off the stop and allow it to engage the notch more . It was as though it was a ramp and allowing the notch to just ride over the stop if you put a bit of rotational pressure on it I fixed it this morning...

The stop goes up and down like it's supposed to and appears to have plenty of tension . Only reason I took to grinding was the stop edge was rounded over a bit so I thought if I took some off the top it would allow it to seat deeper and give a new edge .The notches in the cylinder are fine . The...

I bought a s&w mod 36 on gun broker and the cylinder spins backward .I tore it all apart and took some off the top of the cylinder latch to see if it would engage the notches more to no avail . It wont do it if you pull the trigger all the way through, it locks up ok then .So I'm stumped .What...

Check out the K31's at .. http://www.samcoglobal.com/rifles.html I have three and love them . Great quality rifles and with the money left over you can buy a good scope . Oh ya and Brownells carries two different scope mounts for them . If your right handed I'd recommend the clamp on if your...

The one I was looking at is the Bushnell elite 3200 2-6x32 with the firefly reticle .

I am in the process of putting a scope on a k-31 . I have the scout type mount that replaces the rear sight on the way. Question is what scope do I use ? Are there special scout scopes ? I thought you just used a pistol scope but when I found one that I wanted it said it had a 20 inch eye relief...

HAHAH I can't make up my mind so I ordered all three mounts lol ... I'll decide which one I like the best and sell the others . Someone might get a deal on a scope mount from me if they want . Never thought Id say it but I'm leaning toward the scout setup now. Oh ya other than on gun broker...