Search results for query: *

Spoken For, will mail out this week. LeftyTSGC

I have 50pcs of once fired CBC 44 Rem Mag brass, please PM me if you need them. LeftyTSGC

There is a whole bunch of BE-86 data in the library of wisdom thread, under the BE-86 sticky in THR BE-86 | The High Road https://www.thehighroad.org/index.php?threads/be-86.760289/ Leftytsgc

I have been trying to get to RMR to take advantage of the specials, does anyone know if the site is down? leftytsgc

Thanks for the data, close to what i was planning to start with, i will start at 24.5 and work up from there. I did load up 27.9gn with the Hornady 123 SST. worked well.

I am planning on reloading for a 6.5grendal AR style rifle, I have Norma 120gr 6.5mm .264 bullets, i am using CCI .41primers, am using XBR8208 powder, i can find load data for this Norma bullet, with a oal of 2.230 but not with XBR8208, based on other 6.5 loads i am estimating 26gr load based on...

Dont know if its been mentioned, but in the "Library of Wisdom" is a sticky to "The Plunk Test", which really gives a good explanation on OAL, COAL. As many mentioned, the OAL given by any reloading manual or website is based on what they used to fit their breech, specific to the components they...

Sounds like you have a great space to start a great plan, A lot of great advice from this forum, that is how i got my start 9 years ago. For pistol caliber reloading, i went with a Dillon Square Deal B (SDB), and i use BE-86 powder exclusively for all my pistol loads, 9mm, 38spc, 357mag. Be-86...

I am in southern Alabama, a lot of moisture and heat here. I have used Frog Lube now for about 5 years on all my firearms, and have never had a problem with cleaning or rust, or operations. You just need to know that you have to follow the initial steps on using frog lube and over time it...

I use exclusively, Alliant RL15 - Rifle Alliant BE-86 - 9/38//357 Hodgden Trail Boss -.45LC I have tried Power Pistol Longshot W231 Bullseye Since Hodgden own, Winchester, IMR, Ramshot, Accurate, Westernpoweders and others it narrows down to two distributers. Alliant and Hodgdon. leftytsgc

Akula69 they are yours, please PM me an address to ship too. Leftytsgc

Time to PIF my annual Pulled Bullet stash. These are all pulled for some reason or another of the past year. Bottom row are for 9mm, 115gn, 124gn, 147gn. Also a pile for 40cal mixed weight.. Middle row is .45 Jacketed, Lead, then assortment of small caliber bullets and a few different rifle...

Not so much as i think its out of timing but have a lot of cylinder wear prior to locking up. Looks like the lock bar comes up early and scraps into position to lock the cylinder. It functions and fires fine. Leftytsgc

I have some wear on my cylinder on my 1873 .45LC SAA. Is setting the timing something i can do myself? I have replaced springs and parts on my own before but never messed with the timing. Looking to see if i can tackle it or should I take it to a gunsmith. Are there any videos or such available...

In the Reloading Library of Wisdom Sticky at the front of this forum is a thread on BE-86, there is a bunch of data from all of us here. take a look it may help with what you are trying to accomplish. Leftytsgc

I have Alliant RL15 Powder hat i am currently using for a 130gn Bullet for my 270Win. I am looking to see if anyone has worked a load for a 150gn Bullet using RL15. I contacted Alliant and they have no data for a 150gn bullet for RL15. They didnt say i cant use it but they cannot provide...

I would randomly take 25 bullets and measure the bullet OAL and see what you average and what deviations you have. That may explain the whole issue as some have already mentioned. You can also take a comparator kit and check the seating depth based on the ogive. If your ogive is seating at the...

Thank you for all of those who entered their name into the drawing. The receiver of the RCMODEL press will be CptnAwesome. Please send me a PM with a good shipping address. Congratulations, Leftytsgc

Get your PM to me by Tuesday (tomorrow) 26 January by 1600CST to be added to the drawing. LeftyTSGC

It is great to hear all of the nice comments about RCMODEL. There is still a wealth of information from him in the Library of Wisdom link. If you want your name on the list please PM, so i don't confuse reply's here with being added to list. I am only adding PM requests to the list. LeftyTSGC