Search results for query: *

I have Bullseye and Titegroup

I'm considering these: http://www.shop.rmrbullets.com/40-10mm-180-Gr-Rocky-Mountain-ThunderCast-TCFP-1000-Count-40-180-RMT-TCFP-1000-Ct.htm Thoughts? This will be my first time loading pistol rounds. I've only loaded rifle so far. Would I be better off with a different bullet...

Those pics are exactly what I've got going on, and then some. Some of the brass has a divot taken out of it. I'm going to work back up using .223 data. Hopefully I can find an acceptable load, accuracy wise, using the lower charge weights of the .223 data. I really don't want anything close...

Primer fell out of the case head. The case has been de-primed.

After reading about the nato data I'm going to back it down. I'm just surprised I didn't have any other pressure signs. I would've thought I'd have some flattened primers before blowing them out.

Thank you! This is the first I've seen it.

I'm not over max. http://www.ramshot.com/wp-content/uploads/2010/09/WP_LoadSpec_1-23-14.pdf These are 5.56 chambered ar's. It is mixed brass, and could be part of the problem. Someone mentioned that the nato data is misleading. That's the first I've heard of that. Did Ramshot put out a memo...

Load: 26.5 gr TAC, Hornady 55gr SP, CCi #450, mixed brass I worked up from 24gr to this load. According to Ramshot 27.3 is max in 5.56. It is a good plinking load for 2 AR's. I didn't notice any signs while working up. Over the past week it has really warmed up and I've shot alot. I am...

I bought some last week from a LGS and shot them this past weekend. They are 3/8 ar500 gongs and one silo. The largest caliber I shot was .308. They all held up well to 147gr fmj. No pitting as far as I could tell. My silo has a small chip in the edge, but I don't know which round caused it.

I'd put down 3 bills and see if they took it.

Myself and a friend worked on some 270 loads yesterday. We settled on 54 gr. of IMR4350 and a 130gr. speer hot-cor. I think I could've gotten a little better accuracy but he had to take his girl to the orthodontist.

I got some .270 mixed in with my 30-06 brass while de-capping and resizing. Is the .270 brass ruined? Thanks!

I needed a "both" option. I use an AR15 in 6.8 and a DPMS AR10.

My wife and I attended an Appleseed this past spring. We both loved it. I was worried about equipment because I only own one rimfire, a M&P 15-22. I got in touch with the instructors and they were fine with me using an AR and my wife the M&P. No issues at all. If you're on the fence about going...

I bought some TAC in the spring for $135 for an 8lb keg. I haven't seen an 8lb or TAC at all since then. I have seen some other Ramshot powders. I'm in North Alabama

I'd get in touch with the instructor(s). My wife and I am going to an event in Alabama in May and our instructor sent an email offering ammo at a normal price. They might not have any themselves but could help with getting some.

Thanks for all the help! Exactly what I was looking for. Sounds like Plated projectiles with longshot may be for me.

What are the advantages/disadvantages to FMJ/Cast/Plated projectiles?

I've been reloading rifle rounds for about a year now. I am about to start reloading for my S&W M&P40. I would like to find a load that I can't double charge without overflowing. I am also lost when it comes to what projectiles I would like to use. I am not looking to get into casting my own. I...

I bought 2,000 cci small pistol today for $66 total. Two other stores I visited today were selling them for $40+/1000. I am in north Alabama.